Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) — 3 mm 4-Flute Speeds & Feeds

ISO Group P 280-320 HB / 28-32 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
20,160 RPM
Surface Speed: 190 m/min (623.4 SFM)
Table Feed Rate F = RPM·z·fz
1,081 mm/min
42.7 IPM
Plunge/Ramp Rate: 378 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0134 mm/t
0.00053 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
3.65 cm³/min
0.22 in³/min
Power Required: 0.16 kW (0.21 HP)
Direct CNC Machining Solution

For milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 20,160 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 1,081 mm/min (42.7 IPM) and adjusted chip load of 0.0134 mm/tooth, achieving a material removal rate of 3.65 cm³/min (0.22 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.06 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (190 × 1000) / (π × 3) = 20,160 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0116 mm × 1.1547 = 0.0134 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 20,160 × 4 × 0.0134 = 1,081 mm/min (42.7 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 1081) / 1000 = 3.65 cm³/min (0.22 in³/min)
Specific Cutting Force (kc) for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC): 2100 N/mm². Spindle drive efficiency η = 0.80.

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 351 13.7 1.58 0.07
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 526 20.6 2.37 0.1
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 702 27.4 3.16 0.14
Profiling / HEM (25% WOC) 2F 0.75 mm 4.5 mm 1.1547× 540 21.4 1.82 0.08
Profiling / HEM (25% WOC) 3F 0.75 mm 4.5 mm 1.1547× 810 32.1 2.73 0.12
Profiling / HEM (25% WOC) CURRENT 4F 0.75 mm 4.5 mm 1.1547× 1,081 42.7 3.65 0.16
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 778 30.6 1.4 0.06
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 1,167 46 2.1 0.09
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 1,556 61.3 2.8 0.12

Shop-Floor Machining Strategy for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)

Work Hardening: Moderate-High
Coolant & Lubrication Protocol

Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS

Pressure: 6 bar air blast or 20 bar high-pressure flood

Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Short curled chips form with proper feed; excellent surface finish potential.

Milling Direction: Climb milling essential to enter at thickest chip portion.

Expert Machinist Tips:
  • Pre-hardened 4140 (HT) machines cleanly with rigid setups and AlTiN or TiAlN coated tooling.
  • Use high-efficiency milling (HEM): 8-12% ae radial engagement with 1.5x-2.0x ap depth of cut.
  • Keep tool stickout as short as possible to eliminate chatter harmonics.

Frequently Asked CNC Questions (4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) / 3 mm)

What is the recommended RPM for milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC), the baseline surface cutting speed is 190 m/min (623.4 SFM), which translates to a calculated spindle speed of 20,160 RPM. If using uncoated carbide, reduce surface speed to 150 m/min (500 SFM / 15915 RPM). For HSS cutters, speed must be restricted to 24 m/min (2546 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
At 20,160 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0134 mm/tooth (0.00053"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 1081 mm/min (42.7 IPM). Ramping or plunging into material should be limited to 35% of table feed (378 mm/min / 14.9 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS. Pressure specification: 6 bar air blast or 20 bar high-pressure flood. Engineering rationale: Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.