1018 Mild Carbon Steel (Cold Rolled) — 3 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 1018 Mild Carbon Steel (Cold Rolled) with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 25,465 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 1,548 mm/min (61.1 IPM) and adjusted chip load of 0.0152 mm/tooth, achieving a material removal rate of 5.22 cm³/min (0.32 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math1018 Mild Carbon Steel (Cold Rolled) (3 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3 mm | 1.5 mm | 1× | 504 | 19.9 | 2.27 | 0.07 |
| Slotting (100% WOC) | 3F | 3 mm | 1.5 mm | 1× | 756 | 29.8 | 3.4 | 0.11 |
| Slotting (100% WOC) | 4F | 3 mm | 1.5 mm | 1× | 1,008 | 39.7 | 4.54 | 0.14 |
| Profiling / HEM (25% WOC) | 2F | 0.75 mm | 4.5 mm | 1.1547× | 774 | 30.6 | 2.61 | 0.08 |
| Profiling / HEM (25% WOC) | 3F | 0.75 mm | 4.5 mm | 1.1547× | 1,161 | 45.8 | 3.92 | 0.12 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 0.75 mm | 4.5 mm | 1.1547× | 1,548 | 61.1 | 5.22 | 0.16 |
| Adaptive Clearing (10% WOC) | 2F | 0.3 mm | 6 mm | 1.6667× | 1,120 | 44.3 | 2.02 | 0.06 |
| Adaptive Clearing (10% WOC) | 3F | 0.3 mm | 6 mm | 1.6667× | 1,681 | 66.5 | 3.03 | 0.09 |
| Adaptive Clearing (10% WOC) | 4F | 0.3 mm | 6 mm | 1.6667× | 2,241 | 88.6 | 4.03 | 0.13 |
Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)
Work Hardening: ModerateFlood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide
Pressure: 5 to 10 bar
With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.
Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.
Milling Direction: Always climb mill to manage tool heat dissipation into chips.
- Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
- TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
- 4-flute end mills deliver the best surface finish and wall straightness.
Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 3 mm)
What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 3 mm end mill?
What table feed rate and chip load should I program for 3 mm in 1018 Mild Carbon Steel (Cold Rolled)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Recent Calculations
No recent calculations saved yet.