Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 3 mm 4-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
61,540 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
4,800 mm/min
189.5 IPM
Plunge/Ramp Rate: 1680 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0195 mm/t
0.00077 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
16.2 cm³/min
0.99 in³/min
Power Required: 0.29 kW (0.38 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 61,540 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 4,800 mm/min (189.5 IPM) and adjusted chip load of 0.0195 mm/tooth, achieving a material removal rate of 16.2 cm³/min (0.99 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.04 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 3) = 61,540 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0169 mm × 1.1547 = 0.0195 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 61,540 × 4 × 0.0195 = 4,800 mm/min (189.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 4800) / 1000 = 16.2 cm³/min (0.99 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 1,551 61.5 6.98 0.12
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 2,326 92.3 10.47 0.19
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 3,102 123.1 13.96 0.25
Profiling / HEM (25% WOC) 2F 0.75 mm 4.5 mm 1.1547× 2,400 94.8 8.1 0.14
Profiling / HEM (25% WOC) 3F 0.75 mm 4.5 mm 1.1547× 3,600 142.2 12.15 0.22
Profiling / HEM (25% WOC) CURRENT 4F 0.75 mm 4.5 mm 1.1547× 4,800 189.5 16.2 0.29
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 3,471 136.6 6.25 0.11
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 5,206 204.9 9.37 0.17
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 6,942 273.2 12.5 0.22

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 3 mm)

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 61,540 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 50930 RPM). For HSS cutters, speed must be restricted to 100 m/min (10610 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in 7075-T6 Aerospace Aluminum?
At 61,540 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0195 mm/tooth (0.00077"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 4800 mm/min (189.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (1680 mm/min / 66.3 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.