6061-T6 Aluminum — 3 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 3 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 68,967 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 2,883 mm/min (113.1 IPM) and adjusted chip load of 0.0209 mm/tooth, achieving a material removal rate of 9.73 cm³/min (0.59 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (3 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3 mm | 1.5 mm | 1× | 1,862 | 73.1 | 8.38 | 0.12 |
| Slotting (100% WOC) | 3F | 3 mm | 1.5 mm | 1× | 2,793 | 109.7 | 12.57 | 0.18 |
| Slotting (100% WOC) | 4F | 3 mm | 1.5 mm | 1× | 3,724 | 146.2 | 16.76 | 0.24 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.75 mm | 4.5 mm | 1.1547× | 2,883 | 113.1 | 9.73 | 0.14 |
| Profiling / HEM (25% WOC) | 3F | 0.75 mm | 4.5 mm | 1.1547× | 4,324 | 169.7 | 14.59 | 0.21 |
| Profiling / HEM (25% WOC) | 4F | 0.75 mm | 4.5 mm | 1.1547× | 5,766 | 226.2 | 19.46 | 0.28 |
| Adaptive Clearing (10% WOC) | 2F | 0.3 mm | 6 mm | 1.6667× | 4,166 | 164.1 | 7.5 | 0.11 |
| Adaptive Clearing (10% WOC) | 3F | 0.3 mm | 6 mm | 1.6667× | 6,248 | 246.2 | 11.25 | 0.16 |
| Adaptive Clearing (10% WOC) | 4F | 0.3 mm | 6 mm | 1.6667× | 8,331 | 328.3 | 15 | 0.22 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 3 mm)
What is the recommended RPM for milling 6061-T6 Aluminum with a 3 mm end mill?
What table feed rate and chip load should I program for 3 mm in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.