6061-T6 Aluminum — 5/8" (0.625 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 5/8" (0.625 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 13,033 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 3,093 mm/min (121.6 IPM) and adjusted chip load of 0.0791 mm/tooth, achieving a material removal rate of 292.37 cm³/min (17.82 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (5/8" (0.625 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 15.88 mm | 7.94 mm | 1× | 1,340 | 52.7 | 168.96 | 2.46 |
| Slotting (100% WOC) | 3F | 15.88 mm | 7.94 mm | 1× | 2,010 | 79 | 253.44 | 3.7 |
| Slotting (100% WOC) | 4F | 15.88 mm | 7.94 mm | 1× | 2,680 | 105.3 | 337.91 | 4.93 |
| Profiling / HEM (25% WOC) | 2F | 3.97 mm | 23.81 mm | 1.1546× | 2,062 | 81.1 | 194.91 | 2.84 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 3.97 mm | 23.81 mm | 1.1546× | 3,093 | 121.6 | 292.37 | 4.26 |
| Profiling / HEM (25% WOC) | 4F | 3.97 mm | 23.81 mm | 1.1546× | 4,124 | 162.1 | 389.82 | 5.68 |
| Adaptive Clearing (10% WOC) | 2F | 1.59 mm | 31.75 mm | 1.6655× | 2,974 | 117 | 150.13 | 2.19 |
| Adaptive Clearing (10% WOC) | 3F | 1.59 mm | 31.75 mm | 1.6655× | 4,461 | 175.6 | 225.2 | 3.28 |
| Adaptive Clearing (10% WOC) | 4F | 1.59 mm | 31.75 mm | 1.6655× | 5,948 | 234.1 | 300.27 | 4.38 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 5/8" (0.625 in))
What is the recommended RPM for milling 6061-T6 Aluminum with a 5/8" (0.625 in) end mill?
What table feed rate and chip load should I program for 5/8" (0.625 in) in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.