6061-T6 Aluminum — 3/4" (0.750 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 3/4" (0.750 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 10,861 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 2,981 mm/min (117.3 IPM) and adjusted chip load of 0.0915 mm/tooth, achieving a material removal rate of 405.54 cm³/min (24.73 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (3/4" (0.750 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 19.05 mm | 9.53 mm | 1× | 1,290 | 50.8 | 234.19 | 3.42 |
| Slotting (100% WOC) | 3F | 19.05 mm | 9.53 mm | 1× | 1,935 | 76.2 | 351.29 | 5.12 |
| Slotting (100% WOC) | 4F | 19.05 mm | 9.53 mm | 1× | 2,581 | 101.7 | 468.57 | 6.83 |
| Profiling / HEM (25% WOC) | 2F | 4.76 mm | 28.58 mm | 1.1549× | 1,988 | 78.2 | 270.45 | 3.94 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 4.76 mm | 28.58 mm | 1.1549× | 2,981 | 117.3 | 405.54 | 5.91 |
| Profiling / HEM (25% WOC) | 4F | 4.76 mm | 28.58 mm | 1.1549× | 3,975 | 156.4 | 540.76 | 7.89 |
| Adaptive Clearing (10% WOC) | 2F | 1.91 mm | 38.1 mm | 1.6647× | 2,863 | 112.7 | 208.34 | 3.04 |
| Adaptive Clearing (10% WOC) | 3F | 1.91 mm | 38.1 mm | 1.6647× | 4,294 | 169.1 | 312.48 | 4.56 |
| Adaptive Clearing (10% WOC) | 4F | 1.91 mm | 38.1 mm | 1.6647× | 5,726 | 225.5 | 416.69 | 6.08 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 3/4" (0.750 in))
What is the recommended RPM for milling 6061-T6 Aluminum with a 3/4" (0.750 in) end mill?
What table feed rate and chip load should I program for 3/4" (0.750 in) in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.