Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 5/8" (0.625 in) 3-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
11,630 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
2,575 mm/min
101.5 IPM
Plunge/Ramp Rate: 901 mm/min
Adjusted Chip Load CTF: 1.1546×
0.0738 mm/t
0.00291 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
243.4 cm³/min
14.87 in³/min
Power Required: 4.31 kW (5.78 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 5/8" (0.625 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 11,630 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 2,575 mm/min (101.5 IPM) and adjusted chip load of 0.0738 mm/tooth, achieving a material removal rate of 243.4 cm³/min (14.87 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 15.875 mm (0.625") ae = 3.97 mm ap = 23.81 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1546×
Spindle Torque 2.83 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 15.875) = 11,630 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.97/15.875 = 0.25 → CTF = 1.1546×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0639 mm × 1.1546 = 0.0738 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 11,630 × 3 × 0.0738 = 2,575 mm/min (101.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (23.81 × 3.97 × 2575) / 1000 = 243.4 cm³/min (14.87 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (5/8" (0.625 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 5/8" (0.625 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 15.88 mm 7.94 mm 1× 1,114 44 140.46 2.49
Slotting (100% WOC) 3F 15.88 mm 7.94 mm 1× 1,671 65.9 210.69 3.73
Slotting (100% WOC) 4F 15.88 mm 7.94 mm 1× 2,228 87.9 280.92 4.97
Profiling / HEM (25% WOC) 2F 3.97 mm 23.81 mm 1.1546× 1,717 67.7 162.3 2.87
Profiling / HEM (25% WOC) CURRENT 3F 3.97 mm 23.81 mm 1.1546× 2,575 101.5 243.4 4.31
Profiling / HEM (25% WOC) 4F 3.97 mm 23.81 mm 1.1546× 3,433 135.4 324.51 5.75
Adaptive Clearing (10% WOC) 2F 1.59 mm 31.75 mm 1.6655× 2,475 97.5 124.94 2.21
Adaptive Clearing (10% WOC) 3F 1.59 mm 31.75 mm 1.6655× 3,712 146.2 187.39 3.32
Adaptive Clearing (10% WOC) 4F 1.59 mm 31.75 mm 1.6655× 4,950 194.9 249.89 4.43

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 5/8" (0.625 in))

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 5/8" (0.625 in) end mill?
For a 5/8" (0.625 in) (15.875 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 11,630 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 9624 RPM). For HSS cutters, speed must be restricted to 100 m/min (2005 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 5/8" (0.625 in) in 7075-T6 Aerospace Aluminum?
At 11,630 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0738 mm/tooth (0.00291"/tooth) after applying a radial chip thinning factor (CTF) of 1.1546×. This yields a table feed rate of 2575 mm/min (101.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (901 mm/min / 35.5 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.97 mm), the Chip Thinning Factor is 1.1546×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.