Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

A36 Hot Rolled Structural Steel — 6 mm 2-Flute Speeds & Feeds

ISO Group P 137 HB / 76 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
11,671 RPM
Surface Speed: 220 m/min (721.8 SFM)
Table Feed Rate F = RPM·z·fz
588 mm/min
23.1 IPM
Plunge/Ramp Rate: 206 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0252 mm/t
0.00099 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
7.94 cm³/min
0.48 in³/min
Power Required: 0.27 kW (0.37 HP)
Direct CNC Machining Solution

For milling A36 Hot Rolled Structural Steel with a 6 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 11,671 RPM at 220 m/min (721.8 SFM), with a profiling feed rate of 588 mm/min (23.1 IPM) and adjusted chip load of 0.0252 mm/tooth, achieving a material removal rate of 7.94 cm³/min (0.48 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
A36 Hot Rolled Structural Steel Stock CLIMB D = 6 mm (0.2362") ae = 1.5 mm ap = 9 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.18 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (220 × 1000) / (π × 6) = 11,671 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.5/6 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0218 mm × 1.1547 = 0.0252 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 11,671 × 2 × 0.0252 = 588 mm/min (23.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9 × 1.5 × 588) / 1000 = 7.94 cm³/min (0.48 in³/min)
Specific Cutting Force (kc) for A36 Hot Rolled Structural Steel: 1650 N/mm². Spindle drive efficiency η = 0.80.

A36 Hot Rolled Structural Steel (6 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 6 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6 mm 3 mm 1× 383 15.2 6.89 0.24
Slotting (100% WOC) 3F 6 mm 3 mm 1× 574 22.8 10.33 0.36
Slotting (100% WOC) 4F 6 mm 3 mm 1× 766 30.3 13.79 0.47
Profiling / HEM (25% WOC) CURRENT 2F 1.5 mm 9 mm 1.1547× 588 23.1 7.94 0.27
Profiling / HEM (25% WOC) 3F 1.5 mm 9 mm 1.1547× 882 34.7 11.91 0.41
Profiling / HEM (25% WOC) 4F 1.5 mm 9 mm 1.1547× 1,176 46.2 15.88 0.55
Adaptive Clearing (10% WOC) 2F 0.6 mm 12 mm 1.6667× 847 33.4 6.1 0.21
Adaptive Clearing (10% WOC) 3F 0.6 mm 12 mm 1.6667× 1,271 50.1 9.15 0.31
Adaptive Clearing (10% WOC) 4F 0.6 mm 12 mm 1.6667× 1,695 66.8 12.2 0.42

Shop-Floor Machining Strategy for A36 Hot Rolled Structural Steel

Work Hardening: Moderate
Coolant & Lubrication Protocol

Heavy Flood Coolant with Emulsion

Pressure: 5 to 10 bar

Abrasive black mill scale rapidly destroys cutting edges. Cut beneath the scale on the first pass.

Chip Evacuation & Tool Path Guidance

Chip Flow: Longer chips; ensure adequate chip breaking via aggressive feed rates.

Milling Direction: Climb milling mandatory.

Expert Machinist Tips:
  • CRITICAL: Set first roughing depth of cut at least 1.5 mm to penetrate underneath the abrasive mill scale.
  • Do not skin cut through mill scale; it will instantly dull carbide corner radiuses.
  • Use corner radius end mills (0.5 mm or 0.030" radius) to reinforce cutting corners.

Frequently Asked CNC Questions (A36 Hot Rolled Structural Steel / 6 mm)

What is the recommended RPM for milling A36 Hot Rolled Structural Steel with a 6 mm end mill?
For a 6 mm (6 mm) TiAlN coated carbide end mill in A36 Hot Rolled Structural Steel, the baseline surface cutting speed is 220 m/min (721.8 SFM), which translates to a calculated spindle speed of 11,671 RPM. If using uncoated carbide, reduce surface speed to 180 m/min (600 SFM / 9549 RPM). For HSS cutters, speed must be restricted to 30 m/min (1592 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 6 mm in A36 Hot Rolled Structural Steel?
At 11,671 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0252 mm/tooth (0.00099"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 588 mm/min (23.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (206 mm/min / 8.1 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining A36 Hot Rolled Structural Steel?
Heavy Flood Coolant with Emulsion. Pressure specification: 5 to 10 bar. Engineering rationale: Abrasive black mill scale rapidly destroys cutting edges. Cut beneath the scale on the first pass.