C11000 Electrolytic Tough Pitch (ETP) Copper — 1/4" (0.250 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/4" (0.250 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 12,532 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 1,138 mm/min (44.6 IPM) and adjusted chip load of 0.0227 mm/tooth, achieving a material removal rate of 17.23 cm³/min (1.05 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 371 | 14.5 | 7.47 | 0.17 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 556 | 21.8 | 11.19 | 0.26 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 742 | 29.1 | 14.94 | 0.34 |
| Profiling / HEM (25% WOC) | 2F | 1.59 mm | 9.52 mm | 1.1541× | 569 | 22.3 | 8.61 | 0.2 |
| Profiling / HEM (25% WOC) | 3F | 1.59 mm | 9.52 mm | 1.1541× | 853 | 33.5 | 12.91 | 0.3 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.59 mm | 9.52 mm | 1.1541× | 1,138 | 44.6 | 17.23 | 0.39 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 820 | 32.3 | 6.66 | 0.15 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 1,229 | 48.5 | 9.99 | 0.23 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 1,639 | 64.7 | 13.32 | 0.31 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 1/4" (0.250 in))
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.