Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C11000 Electrolytic Tough Pitch (ETP) Copper — 3/8" (0.375 in) 4-Flute Speeds & Feeds

ISO Group N 50 HB / 40 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
8,355 RPM
Surface Speed: 250 m/min (820.2 SFM)
Table Feed Rate F = RPM·z·fz
1,053 mm/min
41.4 IPM
Plunge/Ramp Rate: 369 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0315 mm/t
0.00124 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
35.81 cm³/min
2.18 in³/min
Power Required: 0.82 kW (1.1 HP)
Direct CNC Machining Solution

For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3/8" (0.375 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 8,355 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 1,053 mm/min (41.4 IPM) and adjusted chip load of 0.0315 mm/tooth, achieving a material removal rate of 35.81 cm³/min (2.18 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C11000 Electrolytic Tough Pitch (ETP) Copper Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.75 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (250 × 1000) / (π × 9.525) = 8,355 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0273 mm × 1.1549 = 0.0315 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 8,355 × 4 × 0.0315 = 1,053 mm/min (41.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 1053) / 1000 = 35.81 cm³/min (2.18 in³/min)
Specific Cutting Force (kc) for C11000 Electrolytic Tough Pitch (ETP) Copper: 1100 N/mm². Spindle drive efficiency η = 0.80.

C11000 Electrolytic Tough Pitch (ETP) Copper (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 343 13.5 15.56 0.36
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 514 20.3 23.32 0.53
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 685 27.1 31.07 0.71
Profiling / HEM (25% WOC) 2F 2.38 mm 14.29 mm 1.1549× 526 20.7 17.89 0.41
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 790 31.1 26.87 0.62
Profiling / HEM (25% WOC) CURRENT 4F 2.38 mm 14.29 mm 1.1549× 1,053 41.4 35.81 0.82
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 762 30.1 13.79 0.32
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 1,143 45.1 20.69 0.47
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 1,524 60.2 27.58 0.63

Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper

Work Hardening: Moderate
Coolant & Lubrication Protocol

Abundant Flood Coolant with High Lubricity Emulsion or Mineral Oil

Pressure: Flood at 8 bar minimum

Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.

Chip Evacuation & Tool Path Guidance

Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.

Milling Direction: Climb milling with high positive rake angles.

Expert Machinist Tips:
  • Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
  • Keep feed rate positive to shear rather than plow or smear the copper grain structure.
  • Program chamfering passes immediately following roughing before secondary operations.

Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 3/8" (0.375 in))

What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in C11000 Electrolytic Tough Pitch (ETP) Copper, the baseline surface cutting speed is 250 m/min (820.2 SFM), which translates to a calculated spindle speed of 8,355 RPM. If using uncoated carbide, reduce surface speed to 200 m/min (650 SFM / 6684 RPM). For HSS cutters, speed must be restricted to 45 m/min (1504 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
At 8,355 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0315 mm/tooth (0.00124"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 1053 mm/min (41.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (369 mm/min / 14.5 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Abundant Flood Coolant with High Lubricity Emulsion or Mineral Oil. Pressure specification: Flood at 8 bar minimum. Engineering rationale: Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.