Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C36000 Free-Cutting Brass — 1/4" (0.250 in) 4-Flute Speeds & Feeds

ISO Group N 120 HB / 78 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
21,054 RPM
Surface Speed: 420 m/min (1378 SFM)
Table Feed Rate F = RPM·z·fz
2,771 mm/min
109.5 IPM
Plunge/Ramp Rate: 970 mm/min
Adjusted Chip Load CTF: 1.1541×
0.0329 mm/t
0.0013 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
41.94 cm³/min
2.57 in³/min
Power Required: 0.66 kW (0.88 HP)
Direct CNC Machining Solution

For milling C36000 Free-Cutting Brass with a 1/4" (0.250 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 21,054 RPM at 420 m/min (1378 SFM), with a profiling feed rate of 2,771 mm/min (109.5 IPM) and adjusted chip load of 0.0329 mm/tooth, achieving a material removal rate of 41.94 cm³/min (2.57 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C36000 Free-Cutting Brass Stock CLIMB D = 6.35 mm (0.25") ae = 1.59 mm ap = 9.52 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1541×
Spindle Torque 0.24 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (420 × 1000) / (π × 6.35) = 21,054 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.59/6.35 = 0.25 → CTF = 1.1541×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0285 mm × 1.1541 = 0.0329 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 21,054 × 4 × 0.0329 = 2,771 mm/min (109.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9.52 × 1.59 × 2771) / 1000 = 41.94 cm³/min (2.57 in³/min)
Specific Cutting Force (kc) for C36000 Free-Cutting Brass: 750 N/mm². Spindle drive efficiency η = 0.80.

C36000 Free-Cutting Brass (1/4" (0.250 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/4" (0.250 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6.35 mm 3.17 mm 1× 901 35.4 18.14 0.28
Slotting (100% WOC) 3F 6.35 mm 3.17 mm 1× 1,352 53.1 27.22 0.43
Slotting (100% WOC) 4F 6.35 mm 3.17 mm 1× 1,802 70.7 36.27 0.57
Profiling / HEM (25% WOC) 2F 1.59 mm 9.52 mm 1.1541× 1,385 54.7 20.96 0.33
Profiling / HEM (25% WOC) 3F 1.59 mm 9.52 mm 1.1541× 2,078 82.1 31.45 0.49
Profiling / HEM (25% WOC) CURRENT 4F 1.59 mm 9.52 mm 1.1541× 2,771 109.5 41.94 0.66
Adaptive Clearing (10% WOC) 2F 0.64 mm 12.7 mm 1.6609× 1,992 78.3 16.19 0.25
Adaptive Clearing (10% WOC) 3F 0.64 mm 12.7 mm 1.6609× 2,988 117.5 24.29 0.38
Adaptive Clearing (10% WOC) 4F 0.64 mm 12.7 mm 1.6609× 3,983 156.6 32.37 0.51

Shop-Floor Machining Strategy for C36000 Free-Cutting Brass

Work Hardening: Very Low
Coolant & Lubrication Protocol

Dry with Air Blast or Light Soluble Flood Coolant

Pressure: Air blast at 4-6 bar

Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces broken powdery needle chips. Air blast keeps work area clear.

Milling Direction: Both climb and conventional work, but climb produces superior Ra finish.

Expert Machinist Tips:
  • Zero rake angle or slightly positive rake tooling prevents cutter self-feeding/grabbing into the material.
  • Spindle speeds can be maxed out on modern CNC centers.
  • Clean chip trays frequently as needle brass chips can clog sump pumps.

Frequently Asked CNC Questions (C36000 Free-Cutting Brass / 1/4" (0.250 in))

What is the recommended RPM for milling C36000 Free-Cutting Brass with a 1/4" (0.250 in) end mill?
For a 1/4" (0.250 in) (6.35 mm) TiAlN coated carbide end mill in C36000 Free-Cutting Brass, the baseline surface cutting speed is 420 m/min (1378 SFM), which translates to a calculated spindle speed of 21,054 RPM. If using uncoated carbide, reduce surface speed to 350 m/min (1150 SFM / 17545 RPM). For HSS cutters, speed must be restricted to 90 m/min (4511 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/4" (0.250 in) in C36000 Free-Cutting Brass?
At 21,054 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0329 mm/tooth (0.0013"/tooth) after applying a radial chip thinning factor (CTF) of 1.1541×. This yields a table feed rate of 2771 mm/min (109.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (970 mm/min / 38.3 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.59 mm), the Chip Thinning Factor is 1.1541×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C36000 Free-Cutting Brass?
Dry with Air Blast or Light Soluble Flood Coolant. Pressure specification: Air blast at 4-6 bar. Engineering rationale: Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.