C11000 Electrolytic Tough Pitch (ETP) Copper — 1/8" (0.125 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 25,064 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 985 mm/min (39.1 IPM) and adjusted chip load of 0.0131 mm/tooth, achieving a material removal rate of 3.7 cm³/min (0.23 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 426 | 16.5 | 2.15 | 0.05 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 639 | 24.8 | 3.22 | 0.07 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 852 | 33.1 | 4.29 | 0.1 |
| Profiling / HEM (25% WOC) | 2F | 0.79 mm | 4.76 mm | 1.1565× | 657 | 26.1 | 2.47 | 0.06 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 0.79 mm | 4.76 mm | 1.1565× | 985 | 39.1 | 3.7 | 0.08 |
| Profiling / HEM (25% WOC) | 4F | 0.79 mm | 4.76 mm | 1.1565× | 1,313 | 52.1 | 4.94 | 0.11 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 942 | 37.1 | 1.91 | 0.04 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 1,414 | 55.6 | 2.87 | 0.07 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 1,885 | 74.2 | 3.83 | 0.09 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 1/8" (0.125 in))
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.