Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C36000 Free-Cutting Brass — 1/8" (0.125 in) 3-Flute Speeds & Feeds

ISO Group N 120 HB / 78 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
42,107 RPM
Surface Speed: 420 m/min (1378 SFM)
Table Feed Rate F = RPM·z·fz
2,400 mm/min
94.7 IPM
Plunge/Ramp Rate: 840 mm/min
Adjusted Chip Load CTF: 1.1565×
0.019 mm/t
0.00075 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
9.02 cm³/min
0.55 in³/min
Power Required: 0.14 kW (0.19 HP)
Direct CNC Machining Solution

For milling C36000 Free-Cutting Brass with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 42,107 RPM at 420 m/min (1378 SFM), with a profiling feed rate of 2,400 mm/min (94.7 IPM) and adjusted chip load of 0.019 mm/tooth, achieving a material removal rate of 9.02 cm³/min (0.55 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C36000 Free-Cutting Brass Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (420 × 1000) / (π × 3.175) = 42,107 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0164 mm × 1.1565 = 0.019 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 42,107 × 3 × 0.019 = 2,400 mm/min (94.7 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 2400) / 1000 = 9.02 cm³/min (0.55 in³/min)
Specific Cutting Force (kc) for C36000 Free-Cutting Brass: 750 N/mm². Spindle drive efficiency η = 0.80.

C36000 Free-Cutting Brass (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 1,036 40.4 5.22 0.08
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 1,554 60.6 7.83 0.12
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 2,072 80.8 10.44 0.16
Profiling / HEM (25% WOC) 2F 0.79 mm 4.76 mm 1.1565× 1,600 63.2 6.02 0.09
Profiling / HEM (25% WOC) CURRENT 3F 0.79 mm 4.76 mm 1.1565× 2,400 94.7 9.02 0.14
Profiling / HEM (25% WOC) 4F 0.79 mm 4.76 mm 1.1565× 3,200 126.3 12.03 0.19
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 2,291 90.1 4.66 0.07
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 3,436 135.2 6.98 0.11
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 4,581 180.2 9.31 0.15

Shop-Floor Machining Strategy for C36000 Free-Cutting Brass

Work Hardening: Very Low
Coolant & Lubrication Protocol

Dry with Air Blast or Light Soluble Flood Coolant

Pressure: Air blast at 4-6 bar

Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces broken powdery needle chips. Air blast keeps work area clear.

Milling Direction: Both climb and conventional work, but climb produces superior Ra finish.

Expert Machinist Tips:
  • Zero rake angle or slightly positive rake tooling prevents cutter self-feeding/grabbing into the material.
  • Spindle speeds can be maxed out on modern CNC centers.
  • Clean chip trays frequently as needle brass chips can clog sump pumps.

Frequently Asked CNC Questions (C36000 Free-Cutting Brass / 1/8" (0.125 in))

What is the recommended RPM for milling C36000 Free-Cutting Brass with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in C36000 Free-Cutting Brass, the baseline surface cutting speed is 420 m/min (1378 SFM), which translates to a calculated spindle speed of 42,107 RPM. If using uncoated carbide, reduce surface speed to 350 m/min (1150 SFM / 35089 RPM). For HSS cutters, speed must be restricted to 90 m/min (9023 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in C36000 Free-Cutting Brass?
At 42,107 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.019 mm/tooth (0.00075"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 2400 mm/min (94.7 IPM). Ramping or plunging into material should be limited to 35% of table feed (840 mm/min / 33.1 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C36000 Free-Cutting Brass?
Dry with Air Blast or Light Soluble Flood Coolant. Pressure specification: Air blast at 4-6 bar. Engineering rationale: Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.