C11000 Electrolytic Tough Pitch (ETP) Copper — 12 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 12 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 6,631 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 756 mm/min (29.8 IPM) and adjusted chip load of 0.038 mm/tooth, achieving a material removal rate of 40.82 cm³/min (2.49 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (12 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12 mm | 6 mm | 1× | 326 | 12.9 | 23.47 | 0.54 |
| Slotting (100% WOC) | 3F | 12 mm | 6 mm | 1× | 489 | 19.3 | 35.21 | 0.81 |
| Slotting (100% WOC) | 4F | 12 mm | 6 mm | 1× | 652 | 25.7 | 46.94 | 1.08 |
| Profiling / HEM (25% WOC) | 2F | 3 mm | 18 mm | 1.1547× | 504 | 19.9 | 27.22 | 0.62 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 3 mm | 18 mm | 1.1547× | 756 | 29.8 | 40.82 | 0.94 |
| Profiling / HEM (25% WOC) | 4F | 3 mm | 18 mm | 1.1547× | 1,008 | 39.8 | 54.43 | 1.25 |
| Adaptive Clearing (10% WOC) | 2F | 1.2 mm | 24 mm | 1.6667× | 727 | 28.6 | 20.94 | 0.48 |
| Adaptive Clearing (10% WOC) | 3F | 1.2 mm | 24 mm | 1.6667× | 1,090 | 43 | 31.39 | 0.72 |
| Adaptive Clearing (10% WOC) | 4F | 1.2 mm | 24 mm | 1.6667× | 1,454 | 57.3 | 41.88 | 0.96 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 12 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 12 mm end mill?
What table feed rate and chip load should I program for 12 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.