Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C36000 Free-Cutting Brass — 12 mm 3-Flute Speeds & Feeds

ISO Group N 120 HB / 78 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
11,141 RPM
Surface Speed: 420 m/min (1378 SFM)
Table Feed Rate F = RPM·z·fz
1,832 mm/min
72.2 IPM
Plunge/Ramp Rate: 641 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0548 mm/t
0.00216 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
98.93 cm³/min
6.04 in³/min
Power Required: 1.55 kW (2.07 HP)
Direct CNC Machining Solution

For milling C36000 Free-Cutting Brass with a 12 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 11,141 RPM at 420 m/min (1378 SFM), with a profiling feed rate of 1,832 mm/min (72.2 IPM) and adjusted chip load of 0.0548 mm/tooth, achieving a material removal rate of 98.93 cm³/min (6.04 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C36000 Free-Cutting Brass Stock CLIMB D = 12 mm (0.4724") ae = 3 mm ap = 18 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 1.06 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (420 × 1000) / (π × 12) = 11,141 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3/12 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0475 mm × 1.1547 = 0.0548 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 11,141 × 3 × 0.0548 = 1,832 mm/min (72.2 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (18 × 3 × 1832) / 1000 = 98.93 cm³/min (6.04 in³/min)
Specific Cutting Force (kc) for C36000 Free-Cutting Brass: 750 N/mm². Spindle drive efficiency η = 0.80.

C36000 Free-Cutting Brass (12 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 12 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 12 mm 6 mm 1× 793 31.2 57.1 0.89
Slotting (100% WOC) 3F 12 mm 6 mm 1× 1,190 46.8 85.68 1.34
Slotting (100% WOC) 4F 12 mm 6 mm 1× 1,586 62.4 114.19 1.78
Profiling / HEM (25% WOC) 2F 3 mm 18 mm 1.1547× 1,221 48.1 65.93 1.03
Profiling / HEM (25% WOC) CURRENT 3F 3 mm 18 mm 1.1547× 1,832 72.2 98.93 1.55
Profiling / HEM (25% WOC) 4F 3 mm 18 mm 1.1547× 2,442 96.3 131.87 2.06
Adaptive Clearing (10% WOC) 2F 1.2 mm 24 mm 1.6667× 1,765 69.5 50.83 0.79
Adaptive Clearing (10% WOC) 3F 1.2 mm 24 mm 1.6667× 2,647 104.3 76.23 1.19
Adaptive Clearing (10% WOC) 4F 1.2 mm 24 mm 1.6667× 3,529 139 101.64 1.59

Shop-Floor Machining Strategy for C36000 Free-Cutting Brass

Work Hardening: Very Low
Coolant & Lubrication Protocol

Dry with Air Blast or Light Soluble Flood Coolant

Pressure: Air blast at 4-6 bar

Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces broken powdery needle chips. Air blast keeps work area clear.

Milling Direction: Both climb and conventional work, but climb produces superior Ra finish.

Expert Machinist Tips:
  • Zero rake angle or slightly positive rake tooling prevents cutter self-feeding/grabbing into the material.
  • Spindle speeds can be maxed out on modern CNC centers.
  • Clean chip trays frequently as needle brass chips can clog sump pumps.

Frequently Asked CNC Questions (C36000 Free-Cutting Brass / 12 mm)

What is the recommended RPM for milling C36000 Free-Cutting Brass with a 12 mm end mill?
For a 12 mm (12 mm) TiAlN coated carbide end mill in C36000 Free-Cutting Brass, the baseline surface cutting speed is 420 m/min (1378 SFM), which translates to a calculated spindle speed of 11,141 RPM. If using uncoated carbide, reduce surface speed to 350 m/min (1150 SFM / 9284 RPM). For HSS cutters, speed must be restricted to 90 m/min (2387 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 12 mm in C36000 Free-Cutting Brass?
At 11,141 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0548 mm/tooth (0.00216"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 1832 mm/min (72.2 IPM). Ramping or plunging into material should be limited to 35% of table feed (641 mm/min / 25.3 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C36000 Free-Cutting Brass?
Dry with Air Blast or Light Soluble Flood Coolant. Pressure specification: Air blast at 4-6 bar. Engineering rationale: Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.