Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Carbon Fiber Reinforced Polymer (CFRP Composite) — 3 mm 2-Flute Speeds & Feeds

ISO Group O / Composites 60-70 HRC (equivalent abrasive wear on tools)

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
20,160 RPM
Surface Speed: 190 m/min (623.4 SFM)
Table Feed Rate F = RPM·z·fz
391 mm/min
15.3 IPM
Plunge/Ramp Rate: 137 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0097 mm/t
0.00038 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
1.32 cm³/min
0.08 in³/min
Power Required: 0.02 kW (0.03 HP)
Direct CNC Machining Solution

For milling Carbon Fiber Reinforced Polymer (CFRP Composite) with a 3 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 20,160 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 391 mm/min (15.3 IPM) and adjusted chip load of 0.0097 mm/tooth, achieving a material removal rate of 1.32 cm³/min (0.08 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Carbon Fiber Reinforced Polymer (CFRP Composite) Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.01 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (190 × 1000) / (π × 3) = 20,160 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0084 mm × 1.1547 = 0.0097 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 20,160 × 2 × 0.0097 = 391 mm/min (15.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 391) / 1000 = 1.32 cm³/min (0.08 in³/min)
Specific Cutting Force (kc) for Carbon Fiber Reinforced Polymer (CFRP Composite): 800 N/mm². Spindle drive efficiency η = 0.80.

Carbon Fiber Reinforced Polymer (CFRP Composite) (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 254 10.1 1.14 0.02
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 381 15.1 1.71 0.03
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 508 20.2 2.29 0.04
Profiling / HEM (25% WOC) CURRENT 2F 0.75 mm 4.5 mm 1.1547× 391 15.3 1.32 0.02
Profiling / HEM (25% WOC) 3F 0.75 mm 4.5 mm 1.1547× 587 23 1.98 0.03
Profiling / HEM (25% WOC) 4F 0.75 mm 4.5 mm 1.1547× 782 30.6 2.64 0.04
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 564 22.2 1.02 0.02
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 847 33.3 1.52 0.03
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 1,129 44.4 2.03 0.03

Shop-Floor Machining Strategy for Carbon Fiber Reinforced Polymer (CFRP Composite)

Work Hardening: Severe abrasive flank wear; abrasive carbon fibers act like grinding grit.
Coolant & Lubrication Protocol

Dry with High-Velocity HEPA Downdraft Dust Collection or DI Water Flood

Pressure: HEPA vacuum pickup nozzle positioned directly at tool tip

WARNING: Airborne carbon dust is electrically conductive (destroys CNC electronics) and an inhalation health hazard. Standard coolant creates a sludge that must be specialty filtered.

Chip Evacuation & Tool Path Guidance

Chip Flow: Carbon fiber does not form chips; it fractures into abrasive micro-powder.

Milling Direction: Compression style (upcut/downcut burr-style) tooling prevents top/bottom ply delamination.

Expert Machinist Tips:
  • Use PCD (polycrystalline diamond) or thick CVD diamond-coated compression router bits.
  • Compression geometry forces top plies downward and bottom plies upward into the part core, eliminating delamination.
  • Inspect cutting edges frequently; worn cutters will tear and push fibers rather than shearing them cleanly.

Frequently Asked CNC Questions (Carbon Fiber Reinforced Polymer (CFRP Composite) / 3 mm)

What is the recommended RPM for milling Carbon Fiber Reinforced Polymer (CFRP Composite) with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in Carbon Fiber Reinforced Polymer (CFRP Composite), the baseline surface cutting speed is 190 m/min (623.4 SFM), which translates to a calculated spindle speed of 20,160 RPM. If using uncoated carbide, reduce surface speed to 160 m/min (520 SFM / 16977 RPM). For HSS cutters, speed must be restricted to 30 m/min (3183 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in Carbon Fiber Reinforced Polymer (CFRP Composite)?
At 20,160 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0097 mm/tooth (0.00038"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 391 mm/min (15.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (137 mm/min / 5.4 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Carbon Fiber Reinforced Polymer (CFRP Composite)?
Dry with High-Velocity HEPA Downdraft Dust Collection or DI Water Flood. Pressure specification: HEPA vacuum pickup nozzle positioned directly at tool tip. Engineering rationale: WARNING: Airborne carbon dust is electrically conductive (destroys CNC electronics) and an inhalation health hazard. Standard coolant creates a sludge that must be specialty filtered.