Delrin (Acetal / Polyoxymethylene / POM-C) — 1/2" (0.500 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/2" (0.500 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 12,532 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 2,820 mm/min (110.9 IPM) and adjusted chip load of 0.075 mm/tooth, achieving a material removal rate of 170.3 cm³/min (10.38 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 1,221 | 48.1 | 98.47 | 0.51 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 1,831 | 72.2 | 147.66 | 0.77 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 2,441 | 96.2 | 196.85 | 1.03 |
| Profiling / HEM (25% WOC) | 2F | 3.17 mm | 19.05 mm | 1.1553× | 1,880 | 73.9 | 113.53 | 0.59 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 3.17 mm | 19.05 mm | 1.1553× | 2,820 | 110.9 | 170.3 | 0.89 |
| Profiling / HEM (25% WOC) | 4F | 3.17 mm | 19.05 mm | 1.1553× | 3,760 | 147.9 | 227.06 | 1.18 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 2,712 | 106.8 | 87.48 | 0.46 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 4,068 | 160.2 | 131.23 | 0.68 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 5,424 | 213.5 | 174.97 | 0.91 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 1/2" (0.500 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.