Delrin (Acetal / Polyoxymethylene / POM-C) — 5/8" (0.625 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 5/8" (0.625 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 10,026 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 2,695 mm/min (106.2 IPM) and adjusted chip load of 0.0896 mm/tooth, achieving a material removal rate of 254.75 cm³/min (15.56 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (5/8" (0.625 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 15.88 mm | 7.94 mm | 1× | 1,167 | 45.9 | 147.14 | 0.77 |
| Slotting (100% WOC) | 3F | 15.88 mm | 7.94 mm | 1× | 1,751 | 68.9 | 220.78 | 1.15 |
| Slotting (100% WOC) | 4F | 15.88 mm | 7.94 mm | 1× | 2,334 | 91.8 | 294.29 | 1.53 |
| Profiling / HEM (25% WOC) | 2F | 3.97 mm | 23.81 mm | 1.1546× | 1,797 | 70.8 | 169.86 | 0.88 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 3.97 mm | 23.81 mm | 1.1546× | 2,695 | 106.2 | 254.75 | 1.33 |
| Profiling / HEM (25% WOC) | 4F | 3.97 mm | 23.81 mm | 1.1546× | 3,593 | 141.6 | 339.63 | 1.77 |
| Adaptive Clearing (10% WOC) | 2F | 1.59 mm | 31.75 mm | 1.6655× | 2,591 | 102.1 | 130.8 | 0.68 |
| Adaptive Clearing (10% WOC) | 3F | 1.59 mm | 31.75 mm | 1.6655× | 3,886 | 153.1 | 196.17 | 1.02 |
| Adaptive Clearing (10% WOC) | 4F | 1.59 mm | 31.75 mm | 1.6655× | 5,181 | 204.1 | 261.55 | 1.36 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 5/8" (0.625 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 5/8" (0.625 in) end mill?
What table feed rate and chip load should I program for 5/8" (0.625 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.