Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Delrin (Acetal / Polyoxymethylene / POM-C) — 1/8" (0.125 in) 4-Flute Speeds & Feeds

ISO Group O 85 Shore D / 120 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
50,128 RPM
Surface Speed: 500 m/min (1640.4 SFM)
Table Feed Rate F = RPM·z·fz
4,953 mm/min
194.5 IPM
Plunge/Ramp Rate: 1734 mm/min
Adjusted Chip Load CTF: 1.1565×
0.0247 mm/t
0.00097 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
18.63 cm³/min
1.13 in³/min
Power Required: 0.1 kW (0.13 HP)
Direct CNC Machining Solution

For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/8" (0.125 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 50,128 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 4,953 mm/min (194.5 IPM) and adjusted chip load of 0.0247 mm/tooth, achieving a material removal rate of 18.63 cm³/min (1.13 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Delrin (Acetal / Polyoxymethylene / POM-C) Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (500 × 1000) / (π × 3.175) = 50,128 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0214 mm × 1.1565 = 0.0247 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 50,128 × 4 × 0.0247 = 4,953 mm/min (194.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 4953) / 1000 = 18.63 cm³/min (1.13 in³/min)
Specific Cutting Force (kc) for Delrin (Acetal / Polyoxymethylene / POM-C): 250 N/mm². Spindle drive efficiency η = 0.80.

Delrin (Acetal / Polyoxymethylene / POM-C) (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 1,614 63.2 8.14 0.04
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 2,421 94.7 12.2 0.06
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 3,228 126.3 16.27 0.08
Profiling / HEM (25% WOC) 2F 0.79 mm 4.76 mm 1.1565× 2,476 97.2 9.31 0.05
Profiling / HEM (25% WOC) 3F 0.79 mm 4.76 mm 1.1565× 3,714 145.9 13.97 0.07
Profiling / HEM (25% WOC) CURRENT 4F 0.79 mm 4.76 mm 1.1565× 4,953 194.5 18.63 0.1
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 3,559 140.4 7.23 0.04
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 5,339 210.5 10.85 0.06
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 7,118 280.7 14.46 0.08

Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)

Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)
Coolant & Lubrication Protocol

Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant

Pressure: Air gun at 5 bar

Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.

Chip Evacuation & Tool Path Guidance

Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.

Milling Direction: Climb milling produces pristine finishes.

Expert Machinist Tips:
  • High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
  • Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
  • Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.

Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 1/8" (0.125 in))

What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in Delrin (Acetal / Polyoxymethylene / POM-C), the baseline surface cutting speed is 500 m/min (1640.4 SFM), which translates to a calculated spindle speed of 50,128 RPM. If using uncoated carbide, reduce surface speed to 450 m/min (1500 SFM / 45115 RPM). For HSS cutters, speed must be restricted to 140 m/min (14036 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
At 50,128 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0247 mm/tooth (0.00097"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 4953 mm/min (194.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (1734 mm/min / 68.1 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant. Pressure specification: Air gun at 5 bar. Engineering rationale: Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.