Delrin (Acetal / Polyoxymethylene / POM-C) — 1/8" (0.125 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 50,128 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 3,714 mm/min (145.9 IPM) and adjusted chip load of 0.0247 mm/tooth, achieving a material removal rate of 13.97 cm³/min (0.85 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 1,614 | 63.2 | 8.14 | 0.04 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 2,421 | 94.7 | 12.2 | 0.06 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 3,228 | 126.3 | 16.27 | 0.08 |
| Profiling / HEM (25% WOC) | 2F | 0.79 mm | 4.76 mm | 1.1565× | 2,476 | 97.2 | 9.31 | 0.05 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 0.79 mm | 4.76 mm | 1.1565× | 3,714 | 145.9 | 13.97 | 0.07 |
| Profiling / HEM (25% WOC) | 4F | 0.79 mm | 4.76 mm | 1.1565× | 4,953 | 194.5 | 18.63 | 0.1 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 3,559 | 140.4 | 7.23 | 0.04 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 5,339 | 210.5 | 10.85 | 0.06 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 7,118 | 280.7 | 14.46 | 0.08 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 1/8" (0.125 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.