Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 1" (1.000 in) 3-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
5,639 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
2,338 mm/min
92 IPM
Plunge/Ramp Rate: 818 mm/min
Adjusted Chip Load CTF: 1.1547×
0.1382 mm/t
0.00544 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
565.64 cm³/min
34.5 in³/min
Power Required: 2.12 kW (2.84 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 1" (1.000 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 5,639 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,338 mm/min (92 IPM) and adjusted chip load of 0.1382 mm/tooth, achieving a material removal rate of 565.64 cm³/min (34.5 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 25.4 mm (1") ae = 6.35 mm ap = 38.1 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 2.88 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 25.4) = 5,639 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 6.35/25.4 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.1197 mm × 1.1547 = 0.1382 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 5,639 × 3 × 0.1382 = 2,338 mm/min (92 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (38.1 × 6.35 × 2338) / 1000 = 565.64 cm³/min (34.5 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (1" (1.000 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1" (1.000 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 25.4 mm 12.7 mm 1× 1,013 39.9 326.77 1.23
Slotting (100% WOC) 3F 25.4 mm 12.7 mm 1× 1,519 59.9 490 1.84
Slotting (100% WOC) 4F 25.4 mm 12.7 mm 1× 2,026 79.8 653.55 2.45
Profiling / HEM (25% WOC) 2F 6.35 mm 38.1 mm 1.1547× 1,559 61.4 377.18 1.41
Profiling / HEM (25% WOC) CURRENT 3F 6.35 mm 38.1 mm 1.1547× 2,338 92 565.64 2.12
Profiling / HEM (25% WOC) 4F 6.35 mm 38.1 mm 1.1547× 3,117 122.7 754.11 2.83
Adaptive Clearing (10% WOC) 2F 2.54 mm 50.8 mm 1.6667× 2,250 88.5 290.32 1.09
Adaptive Clearing (10% WOC) 3F 2.54 mm 50.8 mm 1.6667× 3,375 132.8 435.48 1.63
Adaptive Clearing (10% WOC) 4F 2.54 mm 50.8 mm 1.6667× 4,500 177.1 580.64 2.18

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1" (1.000 in))

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1" (1.000 in) end mill?
For a 1" (1.000 in) (25.4 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 5,639 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 5013 RPM). For HSS cutters, speed must be restricted to 120 m/min (1504 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1" (1.000 in) in HDPE (High-Density Polyethylene)?
At 5,639 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.1382 mm/tooth (0.00544"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 2338 mm/min (92 IPM). Ramping or plunging into material should be limited to 35% of table feed (818 mm/min / 32.2 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 6.35 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.