HDPE (High-Density Polyethylene) — 1" (1.000 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 1" (1.000 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 5,639 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,117 mm/min (122.7 IPM) and adjusted chip load of 0.1382 mm/tooth, achieving a material removal rate of 754.11 cm³/min (46.01 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (1" (1.000 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 25.4 mm | 12.7 mm | 1× | 1,013 | 39.9 | 326.77 | 1.23 |
| Slotting (100% WOC) | 3F | 25.4 mm | 12.7 mm | 1× | 1,519 | 59.9 | 490 | 1.84 |
| Slotting (100% WOC) | 4F | 25.4 mm | 12.7 mm | 1× | 2,026 | 79.8 | 653.55 | 2.45 |
| Profiling / HEM (25% WOC) | 2F | 6.35 mm | 38.1 mm | 1.1547× | 1,559 | 61.4 | 377.18 | 1.41 |
| Profiling / HEM (25% WOC) | 3F | 6.35 mm | 38.1 mm | 1.1547× | 2,338 | 92 | 565.64 | 2.12 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 6.35 mm | 38.1 mm | 1.1547× | 3,117 | 122.7 | 754.11 | 2.83 |
| Adaptive Clearing (10% WOC) | 2F | 2.54 mm | 50.8 mm | 1.6667× | 2,250 | 88.5 | 290.32 | 1.09 |
| Adaptive Clearing (10% WOC) | 3F | 2.54 mm | 50.8 mm | 1.6667× | 3,375 | 132.8 | 435.48 | 1.63 |
| Adaptive Clearing (10% WOC) | 4F | 2.54 mm | 50.8 mm | 1.6667× | 4,500 | 177.1 | 580.64 | 2.18 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1" (1.000 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1" (1.000 in) end mill?
What table feed rate and chip load should I program for 1" (1.000 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.