HDPE (High-Density Polyethylene) — 12 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 12 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 11,937 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 1,812 mm/min (71.4 IPM) and adjusted chip load of 0.0759 mm/tooth, achieving a material removal rate of 97.85 cm³/min (5.98 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (12 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12 mm | 6 mm | 1× | 1,177 | 46.3 | 84.74 | 0.32 |
| Slotting (100% WOC) | 3F | 12 mm | 6 mm | 1× | 1,765 | 69.5 | 127.08 | 0.48 |
| Slotting (100% WOC) | 4F | 12 mm | 6 mm | 1× | 2,354 | 92.6 | 169.49 | 0.64 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 3 mm | 18 mm | 1.1547× | 1,812 | 71.4 | 97.85 | 0.37 |
| Profiling / HEM (25% WOC) | 3F | 3 mm | 18 mm | 1.1547× | 2,718 | 107.1 | 146.77 | 0.55 |
| Profiling / HEM (25% WOC) | 4F | 3 mm | 18 mm | 1.1547× | 3,624 | 142.8 | 195.7 | 0.73 |
| Adaptive Clearing (10% WOC) | 2F | 1.2 mm | 24 mm | 1.6667× | 2,614 | 102.9 | 75.28 | 0.28 |
| Adaptive Clearing (10% WOC) | 3F | 1.2 mm | 24 mm | 1.6667× | 3,921 | 154.3 | 112.92 | 0.42 |
| Adaptive Clearing (10% WOC) | 4F | 1.2 mm | 24 mm | 1.6667× | 5,228 | 205.8 | 150.57 | 0.56 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 12 mm)
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 12 mm end mill?
What table feed rate and chip load should I program for 12 mm in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.