HDPE (High-Density Polyethylene) — 3/16" (0.1875 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 3/16" (0.1875 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 30,080 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,184 mm/min (86 IPM) and adjusted chip load of 0.0363 mm/tooth, achieving a material removal rate of 18.56 cm³/min (1.13 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (3/16" (0.1875 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4.76 mm | 2.38 mm | 1× | 1,414 | 55.9 | 16.02 | 0.06 |
| Slotting (100% WOC) | 3F | 4.76 mm | 2.38 mm | 1× | 2,121 | 83.9 | 24.03 | 0.09 |
| Slotting (100% WOC) | 4F | 4.76 mm | 2.38 mm | 1× | 2,828 | 111.9 | 32.04 | 0.12 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.19 mm | 7.14 mm | 1.1549× | 2,184 | 86 | 18.56 | 0.07 |
| Profiling / HEM (25% WOC) | 3F | 1.19 mm | 7.14 mm | 1.1549× | 3,276 | 129 | 27.83 | 0.1 |
| Profiling / HEM (25% WOC) | 4F | 1.19 mm | 7.14 mm | 1.1549× | 4,368 | 172.1 | 37.11 | 0.14 |
| Adaptive Clearing (10% WOC) | 2F | 0.48 mm | 9.52 mm | 1.6608× | 3,134 | 123.3 | 14.32 | 0.05 |
| Adaptive Clearing (10% WOC) | 3F | 0.48 mm | 9.52 mm | 1.6608× | 4,702 | 185 | 21.49 | 0.08 |
| Adaptive Clearing (10% WOC) | 4F | 0.48 mm | 9.52 mm | 1.6608× | 6,269 | 246.7 | 28.65 | 0.11 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 3/16" (0.1875 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 3/16" (0.1875 in) end mill?
What table feed rate and chip load should I program for 3/16" (0.1875 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.