HDPE (High-Density Polyethylene) — 3/4" (0.750 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 3/4" (0.750 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 7,519 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 1,651 mm/min (65 IPM) and adjusted chip load of 0.1098 mm/tooth, achieving a material removal rate of 224.6 cm³/min (13.71 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (3/4" (0.750 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 19.05 mm | 9.53 mm | 1× | 1,072 | 42.3 | 194.62 | 0.73 |
| Slotting (100% WOC) | 3F | 19.05 mm | 9.53 mm | 1× | 1,608 | 63.4 | 291.93 | 1.09 |
| Slotting (100% WOC) | 4F | 19.05 mm | 9.53 mm | 1× | 2,144 | 84.5 | 389.24 | 1.46 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 4.76 mm | 28.58 mm | 1.1549× | 1,651 | 65 | 224.6 | 0.84 |
| Profiling / HEM (25% WOC) | 3F | 4.76 mm | 28.58 mm | 1.1549× | 2,477 | 97.4 | 336.97 | 1.26 |
| Profiling / HEM (25% WOC) | 4F | 4.76 mm | 28.58 mm | 1.1549× | 3,302 | 129.9 | 449.21 | 1.68 |
| Adaptive Clearing (10% WOC) | 2F | 1.91 mm | 38.1 mm | 1.6647× | 2,381 | 93.7 | 173.27 | 0.65 |
| Adaptive Clearing (10% WOC) | 3F | 1.91 mm | 38.1 mm | 1.6647× | 3,571 | 140.5 | 259.87 | 0.97 |
| Adaptive Clearing (10% WOC) | 4F | 1.91 mm | 38.1 mm | 1.6647× | 4,761 | 187.4 | 346.46 | 1.3 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 3/4" (0.750 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 3/4" (0.750 in) end mill?
What table feed rate and chip load should I program for 3/4" (0.750 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.