Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 4 mm 4-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
35,810 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
4,512 mm/min
177.6 IPM
Plunge/Ramp Rate: 1579 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0315 mm/t
0.00124 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
27.07 cm³/min
1.65 in³/min
Power Required: 0.1 kW (0.14 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 4 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 35,810 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 4,512 mm/min (177.6 IPM) and adjusted chip load of 0.0315 mm/tooth, achieving a material removal rate of 27.07 cm³/min (1.65 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 4 mm (0.1575") ae = 1 mm ap = 6 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 4) = 35,810 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1/4 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0273 mm × 1.1547 = 0.0315 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 35,810 × 4 × 0.0315 = 4,512 mm/min (177.6 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (6 × 1 × 4512) / 1000 = 27.07 cm³/min (1.65 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (4 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 4 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4 mm 2 mm 1× 1,468 58 11.74 0.04
Slotting (100% WOC) 3F 4 mm 2 mm 1× 2,202 87 17.62 0.07
Slotting (100% WOC) 4F 4 mm 2 mm 1× 2,936 116 23.49 0.09
Profiling / HEM (25% WOC) 2F 1 mm 6 mm 1.1547× 2,256 88.8 13.54 0.05
Profiling / HEM (25% WOC) 3F 1 mm 6 mm 1.1547× 3,384 133.2 20.3 0.08
Profiling / HEM (25% WOC) CURRENT 4F 1 mm 6 mm 1.1547× 4,512 177.6 27.07 0.1
Adaptive Clearing (10% WOC) 2F 0.4 mm 8 mm 1.6667× 3,259 128.2 10.43 0.04
Adaptive Clearing (10% WOC) 3F 0.4 mm 8 mm 1.6667× 4,888 192.3 15.64 0.06
Adaptive Clearing (10% WOC) 4F 0.4 mm 8 mm 1.6667× 6,517 256.4 20.85 0.08

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 4 mm)

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 4 mm end mill?
For a 4 mm (4 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 35,810 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 31831 RPM). For HSS cutters, speed must be restricted to 120 m/min (9549 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 4 mm in HDPE (High-Density Polyethylene)?
At 35,810 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0315 mm/tooth (0.00124"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 4512 mm/min (177.6 IPM). Ramping or plunging into material should be limited to 35% of table feed (1579 mm/min / 62.2 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.