HDPE (High-Density Polyethylene) — 6 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 6 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 23,873 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,077 mm/min (81.6 IPM) and adjusted chip load of 0.0435 mm/tooth, achieving a material removal rate of 28.04 cm³/min (1.71 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 1,351 | 53 | 24.32 | 0.09 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 2,027 | 79.5 | 36.49 | 0.14 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 2,702 | 106 | 48.64 | 0.18 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.5 mm | 9 mm | 1.1547× | 2,077 | 81.6 | 28.04 | 0.11 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 3,115 | 122.5 | 42.05 | 0.16 |
| Profiling / HEM (25% WOC) | 4F | 1.5 mm | 9 mm | 1.1547× | 4,154 | 163.3 | 56.08 | 0.21 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 2,998 | 117.9 | 21.59 | 0.08 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 4,498 | 176.9 | 32.39 | 0.12 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 5,997 | 235.9 | 43.18 | 0.16 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 6 mm)
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.