Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 1/8" (0.125 in) 3-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
38,097 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
2,503 mm/min
98.3 IPM
Plunge/Ramp Rate: 876 mm/min
Adjusted Chip Load CTF: 1.1565×
0.0219 mm/t
0.00086 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
9.41 cm³/min
0.57 in³/min
Power Required: 0.06 kW (0.08 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 38,097 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,503 mm/min (98.3 IPM) and adjusted chip load of 0.0219 mm/tooth, achieving a material removal rate of 9.41 cm³/min (0.57 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.01 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 3.175) = 38,097 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0189 mm × 1.1565 = 0.0219 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 38,097 × 3 × 0.0219 = 2,503 mm/min (98.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 2503) / 1000 = 9.41 cm³/min (0.57 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 1,082 42.7 5.45 0.03
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 1,623 64 8.18 0.05
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 2,164 85.3 10.91 0.07
Profiling / HEM (25% WOC) 2F 0.79 mm 4.76 mm 1.1565× 1,669 65.5 6.28 0.04
Profiling / HEM (25% WOC) CURRENT 3F 0.79 mm 4.76 mm 1.1565× 2,503 98.3 9.41 0.06
Profiling / HEM (25% WOC) 4F 0.79 mm 4.76 mm 1.1565× 3,337 131.1 12.55 0.08
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 2,392 94.5 4.86 0.03
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 3,589 141.7 7.29 0.05
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 4,785 189 9.72 0.06

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 1/8" (0.125 in))

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 38,097 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 32082 RPM). For HSS cutters, speed must be restricted to 100 m/min (10026 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in Polycarbonate (Lexan / PC Thermoplastic)?
At 38,097 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0219 mm/tooth (0.00086"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 2503 mm/min (98.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (876 mm/min / 34.4 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.