Polycarbonate (Lexan / PC Thermoplastic) — 1/8" (0.125 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/8" (0.125 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 38,097 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,669 mm/min (65.5 IPM) and adjusted chip load of 0.0219 mm/tooth, achieving a material removal rate of 6.28 cm³/min (0.38 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 1,082 | 42.7 | 5.45 | 0.03 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 1,623 | 64 | 8.18 | 0.05 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 2,164 | 85.3 | 10.91 | 0.07 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.79 mm | 4.76 mm | 1.1565× | 1,669 | 65.5 | 6.28 | 0.04 |
| Profiling / HEM (25% WOC) | 3F | 0.79 mm | 4.76 mm | 1.1565× | 2,503 | 98.3 | 9.41 | 0.06 |
| Profiling / HEM (25% WOC) | 4F | 0.79 mm | 4.76 mm | 1.1565× | 3,337 | 131.1 | 12.55 | 0.08 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 2,392 | 94.5 | 4.86 | 0.03 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 3,589 | 141.7 | 7.29 | 0.05 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 4,785 | 189 | 9.72 | 0.06 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 1/8" (0.125 in))
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.