Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 4 mm 2-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
30,239 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
1,585 mm/min
62.3 IPM
Plunge/Ramp Rate: 555 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0262 mm/t
0.00103 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
9.51 cm³/min
0.58 in³/min
Power Required: 0.06 kW (0.08 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 4 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 30,239 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,585 mm/min (62.3 IPM) and adjusted chip load of 0.0262 mm/tooth, achieving a material removal rate of 9.51 cm³/min (0.58 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 4 mm (0.1575") ae = 1 mm ap = 6 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 4) = 30,239 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1/4 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0227 mm × 1.1547 = 0.0262 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 30,239 × 2 × 0.0262 = 1,585 mm/min (62.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (6 × 1 × 1585) / 1000 = 9.51 cm³/min (0.58 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (4 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 4 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4 mm 2 mm 1× 1,034 40.5 8.27 0.05
Slotting (100% WOC) 3F 4 mm 2 mm 1× 1,551 60.8 12.41 0.08
Slotting (100% WOC) 4F 4 mm 2 mm 1× 2,068 81 16.54 0.1
Profiling / HEM (25% WOC) CURRENT 2F 1 mm 6 mm 1.1547× 1,585 62.3 9.51 0.06
Profiling / HEM (25% WOC) 3F 1 mm 6 mm 1.1547× 2,377 93.4 14.26 0.09
Profiling / HEM (25% WOC) 4F 1 mm 6 mm 1.1547× 3,169 124.6 19.01 0.12
Adaptive Clearing (10% WOC) 2F 0.4 mm 8 mm 1.6667× 2,286 90.1 7.32 0.05
Adaptive Clearing (10% WOC) 3F 0.4 mm 8 mm 1.6667× 3,429 135.2 10.97 0.07
Adaptive Clearing (10% WOC) 4F 0.4 mm 8 mm 1.6667× 4,572 180.2 14.63 0.09

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 4 mm)

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 4 mm end mill?
For a 4 mm (4 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 30,239 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 25465 RPM). For HSS cutters, speed must be restricted to 100 m/min (7958 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 4 mm in Polycarbonate (Lexan / PC Thermoplastic)?
At 30,239 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0262 mm/tooth (0.00103"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 1585 mm/min (62.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (555 mm/min / 21.8 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.