Polycarbonate (Lexan / PC Thermoplastic) — 4 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 4 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 30,239 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 3,169 mm/min (124.6 IPM) and adjusted chip load of 0.0262 mm/tooth, achieving a material removal rate of 19.01 cm³/min (1.16 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 1,034 | 40.5 | 8.27 | 0.05 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 1,551 | 60.8 | 12.41 | 0.08 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 2,068 | 81 | 16.54 | 0.1 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 1,585 | 62.3 | 9.51 | 0.06 |
| Profiling / HEM (25% WOC) | 3F | 1 mm | 6 mm | 1.1547× | 2,377 | 93.4 | 14.26 | 0.09 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1 mm | 6 mm | 1.1547× | 3,169 | 124.6 | 19.01 | 0.12 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 2,286 | 90.1 | 7.32 | 0.05 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 3,429 | 135.2 | 10.97 | 0.07 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 4,572 | 180.2 | 14.63 | 0.09 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 4 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.