Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 6 mm 3-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
20,160 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
2,195 mm/min
86.5 IPM
Plunge/Ramp Rate: 768 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0363 mm/t
0.00143 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
29.63 cm³/min
1.81 in³/min
Power Required: 0.19 kW (0.25 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 6 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 20,160 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,195 mm/min (86.5 IPM) and adjusted chip load of 0.0363 mm/tooth, achieving a material removal rate of 29.63 cm³/min (1.81 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 6 mm (0.2362") ae = 1.5 mm ap = 9 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.07 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 6) = 20,160 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.5/6 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0314 mm × 1.1547 = 0.0363 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 20,160 × 3 × 0.0363 = 2,195 mm/min (86.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9 × 1.5 × 2195) / 1000 = 29.63 cm³/min (1.81 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (6 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 6 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6 mm 3 mm 1× 952 37.5 17.14 0.11
Slotting (100% WOC) 3F 6 mm 3 mm 1× 1,427 56.2 25.69 0.16
Slotting (100% WOC) 4F 6 mm 3 mm 1× 1,903 75 34.25 0.21
Profiling / HEM (25% WOC) 2F 1.5 mm 9 mm 1.1547× 1,464 57.7 19.76 0.12
Profiling / HEM (25% WOC) CURRENT 3F 1.5 mm 9 mm 1.1547× 2,195 86.5 29.63 0.19
Profiling / HEM (25% WOC) 4F 1.5 mm 9 mm 1.1547× 2,927 115.3 39.51 0.25
Adaptive Clearing (10% WOC) 2F 0.6 mm 12 mm 1.6667× 2,109 83.1 15.18 0.09
Adaptive Clearing (10% WOC) 3F 0.6 mm 12 mm 1.6667× 3,163 124.6 22.77 0.14
Adaptive Clearing (10% WOC) 4F 0.6 mm 12 mm 1.6667× 4,217 166.1 30.36 0.19

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 6 mm)

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 6 mm end mill?
For a 6 mm (6 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 20,160 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 16977 RPM). For HSS cutters, speed must be restricted to 100 m/min (5305 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 6 mm in Polycarbonate (Lexan / PC Thermoplastic)?
At 20,160 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0363 mm/tooth (0.00143"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 2195 mm/min (86.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (768 mm/min / 30.3 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.