Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

1/2"-13 UNC Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
102.214 N·m
75.389 ft-lbs | 904.67 in-lbs | 10.4229 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
40.242 kN
9,046.7 lbf
Target tension across joint interface
75% Tap Drill d - P
10.716 mm
27/64" (0.4219 in) (93.8% Eng.)
50% Hard Metal Drill: 11.643 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 1/2"-13 UNC Grade 5 bolt is 102.214 N·m (75.389 ft-lbs) when dry (K=0.20) and 76.661 N·m (56.542 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 40.242 kN (9,046.7 lbf) at 75% proof load. Standard 75% tap drill is 27/64" (0.4219 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 12.7 mm (0.5") P = 1.95385 mm 1/2"-13 UNC Close: 13.106mm Normal: 13.487mm Loose: 14.3mm
Stress Area (As) 91.547 mm²
Pitch Diameter (d2) 11.431 mm
Minor Diameter (d1) 10.585 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (12.7 − 0.9382 × 1.95385)² = 91.547 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 91.547 mm² × 586.1 N/mm² = 53656 N (53.656 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 53656 N = 40242 N (40.242 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 12.7 mm × 40242 N) / 1000 = 102.214 N·m (75.389 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

1/2"-13 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 1/2"-13 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 102.214 Nm
75.389 ft-lb
91.993 Nm
67.85 ft-lb
76.661 Nm
56.542 ft-lb
61.328 Nm
45.234 ft-lb
40.242 53.656
Grade 8 144.296 Nm
106.427 ft-lb
129.866 Nm
95.785 ft-lb
108.222 Nm
79.821 ft-lb
86.578 Nm
63.856 ft-lb
56.809 75.746
18-8 Stainless 54.115 Nm
39.913 ft-lb
48.704 Nm
35.922 ft-lb
40.587 Nm
29.935 ft-lb
32.469 Nm
23.948 ft-lb
21.305 28.407

Frequently Asked Engineering Questions (1/2"-13 UNC Grade 5)

What is the recommended tightening torque for a 1/2"-13 UNC Grade 5 bolt?
For a 1/2"-13 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 102.214 N·m (75.389 ft-lbs / 904.67 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 76.661 N·m (56.542 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 61.328 N·m (45.234 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 1/2"-13 UNC internal threads?
The standard cut tap drill size for 1/2"-13 UNC is 27/64" (0.4219 in) (0.4219" / 10.716 mm), which delivers approximately 93.8% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 11.643 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 1/2"-13 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 91.547 mm² (0.1419 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 1/2"-13 UNC Grade 5 fastener possesses an ultimate proof load of 53.656 kN (12,062.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 40.242 kN (9,046.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for 1/2"-13 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 1/2"-13 UNC fastener are: Close Fit = 13.106 mm (0.516"), Normal Fit = 13.487 mm (0.531"), and Loose Fit = 14.3 mm (0.563"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.