Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

1/2"-20 UNF Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
115.219 N·m
84.981 ft-lbs | 1019.78 in-lbs | 11.7491 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
45.362 kN
10,197.8 lbf
Target tension across joint interface
75% Tap Drill d - P
11.509 mm
29/64" (0.4531 in) (86.6% Eng.)
50% Hard Metal Drill: 12.012 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 1/2"-20 UNF Grade 5 bolt is 115.219 N·m (84.981 ft-lbs) when dry (K=0.20) and 86.414 N·m (63.736 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 45.362 kN (10,197.8 lbf) at 75% proof load. Standard 75% tap drill is 29/64" (0.4531 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 12.7 mm (0.5") P = 1.27 mm 1/2"-20 UNF Close: 13.106mm Normal: 13.487mm Loose: 14.3mm
Stress Area (As) 103.195 mm²
Pitch Diameter (d2) 11.875 mm
Minor Diameter (d1) 11.325 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (12.7 − 0.9382 × 1.27)² = 103.195 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 103.195 mm² × 586.1 N/mm² = 60483 N (60.483 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 60483 N = 45362 N (45.362 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 12.7 mm × 45362 N) / 1000 = 115.219 N·m (84.981 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

1/2"-20 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 1/2"-20 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 115.219 Nm
84.981 ft-lb
103.697 Nm
76.483 ft-lb
86.414 Nm
63.736 ft-lb
69.132 Nm
50.989 ft-lb
45.362 60.483
Grade 8 162.656 Nm
119.969 ft-lb
146.39 Nm
107.972 ft-lb
121.992 Nm
89.976 ft-lb
97.593 Nm
71.981 ft-lb
64.038 85.384
18-8 Stainless 61.001 Nm
44.992 ft-lb
54.901 Nm
40.493 ft-lb
45.751 Nm
33.744 ft-lb
36.6 Nm
26.995 ft-lb
24.016 32.021

Frequently Asked Engineering Questions (1/2"-20 UNF Grade 5)

What is the recommended tightening torque for a 1/2"-20 UNF Grade 5 bolt?
For a 1/2"-20 UNF SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 115.219 N·m (84.981 ft-lbs / 1019.78 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 86.414 N·m (63.736 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 69.132 N·m (50.989 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 1/2"-20 UNF internal threads?
The standard cut tap drill size for 1/2"-20 UNF is 29/64" (0.4531 in) (0.4531" / 11.509 mm), which delivers approximately 86.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 12.012 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 1/2"-20 UNF Grade 5 fastener develop?
With a tensile stress area (As) of 103.195 mm² (0.15995 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 1/2"-20 UNF Grade 5 fastener possesses an ultimate proof load of 60.483 kN (13,597 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 45.362 kN (10,197.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for 1/2"-20 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 1/2"-20 UNF fastener are: Close Fit = 13.106 mm (0.516"), Normal Fit = 13.487 mm (0.531"), and Loose Fit = 14.3 mm (0.563"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.