1/4"-28 UNF Grade 5 Torque & Tap Drill Spec
SAE J429 / ASTM A449Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
13.101 N·m
9.663 ft-lbs | 115.95 in-lbs | 1.3359 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
10.316 kN
2,319 lbf
Target tension across joint interface
75% Tap Drill d - P
5.41 mm
#3 (0.2130 in) (95.7% Eng.)
50% Hard Metal Drill: 5.86 mm
Direct Engineering Specification Summary
The recommended tightening torque for a 1/4"-28 UNF Grade 5 bolt is 13.101 N·m (9.663 ft-lbs) when dry (K=0.20) and 9.826 N·m (7.247 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 10.316 kN (2,319 lbf) at 75% proof load. Standard 75% tap drill is #3 (0.2130 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 23.467 mm²
Pitch Diameter (d2) 5.761 mm
Minor Diameter (d1) 5.368 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (6.35 − 0.9382 × 0.90714)² = 23.467 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 23.467 mm² × 586.1 N/mm² = 13754 N (13.754 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 13754 N = 10316 N (10.316 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 6.35 mm × 10316 N) / 1000 = 13.101 N·m (9.663 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
1/4"-28 UNF Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 CURRENT | 13.101 Nm 9.663 ft-lb | 11.791 Nm 8.696 ft-lb | 9.826 Nm 7.247 ft-lb | 7.86 Nm 5.798 ft-lb | 10.316 | 13.754 |
| Grade 8 | 18.494 Nm 13.641 ft-lb | 16.645 Nm 12.277 ft-lb | 13.871 Nm 10.231 ft-lb | 11.097 Nm 8.184 ft-lb | 14.562 | 19.417 |
| 18-8 Stainless | 6.936 Nm 5.116 ft-lb | 6.242 Nm 4.604 ft-lb | 5.202 Nm 3.837 ft-lb | 4.162 Nm 3.069 ft-lb | 5.461 | 7.282 |
Frequently Asked Engineering Questions (1/4"-28 UNF Grade 5)
What is the recommended tightening torque for a 1/4"-28 UNF Grade 5 bolt?
For a 1/4"-28 UNF SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 13.101 N·m (9.663 ft-lbs / 115.95 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 9.826 N·m (7.247 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 7.86 N·m (5.798 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 1/4"-28 UNF internal threads?
The standard cut tap drill size for 1/4"-28 UNF is #3 (0.2130 in) (0.2130" / 5.41 mm), which delivers approximately 95.7% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 5.86 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 1/4"-28 UNF Grade 5 fastener develop?
With a tensile stress area (As) of 23.467 mm² (0.03637 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 1/4"-28 UNF Grade 5 fastener possesses an ultimate proof load of 13.754 kN (3,092 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 10.316 kN (2,319 lbf) across the joint interface.
What clearance hole diameters should be drilled for 1/4"-28 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 1/4"-28 UNF fastener are: Close Fit = 6.528 mm (0.257"), Normal Fit = 6.756 mm (0.266"), and Loose Fit = 7.137 mm (0.281"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.