Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

1/4"-28 UNF 18-8 Stainless Torque & Tap Drill Spec

ASTM F593 Group 1 / AISI 304

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
6.936 N·m
5.116 ft-lbs | 61.39 in-lbs | 0.7073 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
5.461 kN
1,227.8 lbf
Target tension across joint interface
75% Tap Drill d - P
5.41 mm
#3 (0.2130 in) (95.7% Eng.)
50% Hard Metal Drill: 5.86 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 1/4"-28 UNF 18-8 Stainless bolt is 6.936 N·m (5.116 ft-lbs) when dry (K=0.20) and 5.202 N·m (3.837 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 5.461 kN (1,227.8 lbf) at 75% proof load. Standard 75% tap drill is #3 (0.2130 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 6.35 mm (0.25") P = 0.90714 mm 1/4"-28 UNF Close: 6.528mm Normal: 6.756mm Loose: 7.137mm
Stress Area (As) 23.467 mm²
Pitch Diameter (d2) 5.761 mm
Minor Diameter (d1) 5.368 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (6.35 − 0.9382 × 0.90714)² = 23.467 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 23.467 mm² × 310.3 N/mm² = 7282 N (7.282 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 7282 N = 5461 N (5.461 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 6.35 mm × 5461 N) / 1000 = 6.936 N·m (5.116 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

1/4"-28 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 1/4"-28 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 13.101 Nm
9.663 ft-lb
11.791 Nm
8.696 ft-lb
9.826 Nm
7.247 ft-lb
7.86 Nm
5.798 ft-lb
10.316 13.754
Grade 8 18.494 Nm
13.641 ft-lb
16.645 Nm
12.277 ft-lb
13.871 Nm
10.231 ft-lb
11.097 Nm
8.184 ft-lb
14.562 19.417
18-8 Stainless CURRENT 6.936 Nm
5.116 ft-lb
6.242 Nm
4.604 ft-lb
5.202 Nm
3.837 ft-lb
4.162 Nm
3.069 ft-lb
5.461 7.282

Frequently Asked Engineering Questions (1/4"-28 UNF 18-8 Stainless)

What is the recommended tightening torque for a 1/4"-28 UNF 18-8 Stainless bolt?
For a 1/4"-28 UNF 18-8 Stainless Steel (ASTM F593 Group 1) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 6.936 N·m (5.116 ft-lbs / 61.39 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 5.202 N·m (3.837 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 4.162 N·m (3.069 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 1/4"-28 UNF internal threads?
The standard cut tap drill size for 1/4"-28 UNF is #3 (0.2130 in) (0.2130" / 5.41 mm), which delivers approximately 95.7% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 5.86 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 1/4"-28 UNF 18-8 Stainless fastener develop?
With a tensile stress area (As) of 23.467 mm² (0.03637 in²) and a nominal proof stress of 310.3 MPa (45,000 psi), a 1/4"-28 UNF 18-8 Stainless fastener possesses an ultimate proof load of 7.282 kN (1,637 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 5.461 kN (1,227.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for 1/4"-28 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 1/4"-28 UNF fastener are: Close Fit = 6.528 mm (0.257"), Normal Fit = 6.756 mm (0.266"), and Loose Fit = 7.137 mm (0.281"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.