Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

3/4"-10 UNC Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
361.384 N·m
266.543 ft-lbs | 3198.52 in-lbs | 36.8509 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
94.851 kN
21,323.5 lbf
Target tension across joint interface
75% Tap Drill d - P
16.667 mm
21/32" (0.6562 in) (86.6% Eng.)
50% Hard Metal Drill: 17.676 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 3/4"-10 UNC Grade 5 bolt is 361.384 N·m (266.543 ft-lbs) when dry (K=0.20) and 271.038 N·m (199.907 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 94.851 kN (21,323.5 lbf) at 75% proof load. Standard 75% tap drill is 21/32" (0.6562 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 19.05 mm (0.75") P = 2.54 mm 3/4"-10 UNC Close: 19.456mm Normal: 19.837mm Loose: 20.65mm
Stress Area (As) 215.78 mm²
Pitch Diameter (d2) 17.4 mm
Minor Diameter (d1) 16.3 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (19.05 − 0.9382 × 2.54)² = 215.78 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 215.78 mm² × 586.1 N/mm² = 126469 N (126.469 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 126469 N = 94851 N (94.851 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 19.05 mm × 94851 N) / 1000 = 361.384 N·m (266.543 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

3/4"-10 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 3/4"-10 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 361.384 Nm
266.543 ft-lb
325.246 Nm
239.889 ft-lb
271.038 Nm
199.907 ft-lb
216.831 Nm
159.926 ft-lb
94.851 126.469
Grade 8 510.168 Nm
376.28 ft-lb
459.151 Nm
338.652 ft-lb
382.626 Nm
282.21 ft-lb
306.101 Nm
225.768 ft-lb
133.902 178.536
18-8 Stainless 191.328 Nm
141.117 ft-lb
172.195 Nm
127.005 ft-lb
143.496 Nm
105.837 ft-lb
114.797 Nm
84.67 ft-lb
50.217 66.957

Frequently Asked Engineering Questions (3/4"-10 UNC Grade 5)

What is the recommended tightening torque for a 3/4"-10 UNC Grade 5 bolt?
For a 3/4"-10 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 361.384 N·m (266.543 ft-lbs / 3198.52 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 271.038 N·m (199.907 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 216.831 N·m (159.926 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 3/4"-10 UNC internal threads?
The standard cut tap drill size for 3/4"-10 UNC is 21/32" (0.6562 in) (0.6562" / 16.667 mm), which delivers approximately 86.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 17.676 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 3/4"-10 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 215.78 mm² (0.33446 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 3/4"-10 UNC Grade 5 fastener possesses an ultimate proof load of 126.469 kN (28,431.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 94.851 kN (21,323.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for 3/4"-10 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 3/4"-10 UNC fastener are: Close Fit = 19.456 mm (0.766"), Normal Fit = 19.837 mm (0.781"), and Loose Fit = 20.65 mm (0.813"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.