3/4"-16 UNF Grade 5 Torque & Tap Drill Spec
SAE J429 / ASTM A449Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
402.984 N·m
297.226 ft-lbs | 3566.71 in-lbs | 41.0929 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
105.77 kN
23,778.1 lbf
Target tension across joint interface
75% Tap Drill d - P
17.462 mm
11/16" (0.6875 in) (92.4% Eng.)
50% Hard Metal Drill: 18.191 mm
Direct Engineering Specification Summary
The recommended tightening torque for a 3/4"-16 UNF Grade 5 bolt is 402.984 N·m (297.226 ft-lbs) when dry (K=0.20) and 302.238 N·m (222.919 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 105.77 kN (23,778.1 lbf) at 75% proof load. Standard 75% tap drill is 11/16" (0.6875 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 240.619 mm²
Pitch Diameter (d2) 18.019 mm
Minor Diameter (d1) 17.331 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (19.05 − 0.9382 × 1.5875)² = 240.619 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 240.619 mm² × 586.1 N/mm² = 141027 N (141.027 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 141027 N = 105770 N (105.77 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 19.05 mm × 105770 N) / 1000 = 402.984 N·m (297.226 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
3/4"-16 UNF Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 CURRENT | 402.984 Nm 297.226 ft-lb | 362.686 Nm 267.503 ft-lb | 302.238 Nm 222.919 ft-lb | 241.79 Nm 178.335 ft-lb | 105.77 | 141.027 |
| Grade 8 | 568.894 Nm 419.595 ft-lb | 512.005 Nm 377.635 ft-lb | 426.671 Nm 314.696 ft-lb | 341.337 Nm 251.757 ft-lb | 149.316 | 199.088 |
| 18-8 Stainless | 213.353 Nm 157.361 ft-lb | 192.017 Nm 141.625 ft-lb | 160.014 Nm 118.021 ft-lb | 128.012 Nm 94.416 ft-lb | 55.998 | 74.664 |
Frequently Asked Engineering Questions (3/4"-16 UNF Grade 5)
What is the recommended tightening torque for a 3/4"-16 UNF Grade 5 bolt?
For a 3/4"-16 UNF SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 402.984 N·m (297.226 ft-lbs / 3566.71 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 302.238 N·m (222.919 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 241.79 N·m (178.335 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 3/4"-16 UNF internal threads?
The standard cut tap drill size for 3/4"-16 UNF is 11/16" (0.6875 in) (0.6875" / 17.462 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 18.191 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 3/4"-16 UNF Grade 5 fastener develop?
With a tensile stress area (As) of 240.619 mm² (0.37296 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 3/4"-16 UNF Grade 5 fastener possesses an ultimate proof load of 141.027 kN (31,704.1 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 105.77 kN (23,778.1 lbf) across the joint interface.
What clearance hole diameters should be drilled for 3/4"-16 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 3/4"-16 UNF fastener are: Close Fit = 19.456 mm (0.766"), Normal Fit = 19.837 mm (0.781"), and Loose Fit = 20.65 mm (0.813"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.