Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

#4-40 UNC Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
0.973 N·m
0.718 ft-lbs | 8.62 in-lbs | 0.0993 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
1.711 kN
384.6 lbf
Target tension across joint interface
75% Tap Drill d - P
2.261 mm
#43 (0.0890 in) (85% Eng.)
50% Hard Metal Drill: 2.502 mm
Direct Engineering Specification Summary

The recommended tightening torque for a #4-40 UNC Grade 5 bolt is 0.973 N·m (0.718 ft-lbs) when dry (K=0.20) and 0.73 N·m (0.538 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 1.711 kN (384.6 lbf) at 75% proof load. Standard 75% tap drill is #43 (0.0890 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 2.8448 mm (0.112") P = 0.635 mm #4-40 UNC Close: 3.048mm Normal: 3.264mm Loose: 3.658mm
Stress Area (As) 3.892 mm²
Pitch Diameter (d2) 2.432 mm
Minor Diameter (d1) 2.157 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (2.8448 − 0.9382 × 0.635)² = 3.892 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 3.892 mm² × 586.1 N/mm² = 2281 N (2.281 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 2281 N = 1711 N (1.711 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 2.8448 mm × 1711 N) / 1000 = 0.973 N·m (0.718 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

#4-40 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: #4-40 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 0.973 Nm
0.718 ft-lb
0.876 Nm
0.646 ft-lb
0.73 Nm
0.538 ft-lb
0.584 Nm
0.431 ft-lb
1.711 2.281
Grade 8 1.374 Nm
1.014 ft-lb
1.237 Nm
0.912 ft-lb
1.031 Nm
0.76 ft-lb
0.824 Nm
0.608 ft-lb
2.415 3.22
18-8 Stainless 0.515 Nm
0.38 ft-lb
0.464 Nm
0.342 ft-lb
0.387 Nm
0.285 ft-lb
0.309 Nm
0.228 ft-lb
0.906 1.208

Frequently Asked Engineering Questions (#4-40 UNC Grade 5)

What is the recommended tightening torque for a #4-40 UNC Grade 5 bolt?
For a #4-40 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 0.973 N·m (0.718 ft-lbs / 8.62 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 0.73 N·m (0.538 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 0.584 N·m (0.431 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #4-40 UNC internal threads?
The standard cut tap drill size for #4-40 UNC is #43 (0.0890 in) (0.0890" / 2.261 mm), which delivers approximately 85% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 2.502 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #4-40 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 3.892 mm² (0.00603 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a #4-40 UNC Grade 5 fastener possesses an ultimate proof load of 2.281 kN (512.8 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 1.711 kN (384.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for #4-40 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #4-40 UNC fastener are: Close Fit = 3.048 mm (0.12"), Normal Fit = 3.264 mm (0.1285"), and Loose Fit = 3.658 mm (0.144"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.