#4-40 UNC Grade 8 Torque & Tap Drill Spec
SAE J429 / ASTM A354 Grade BDLive Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
1.374 N·m
1.014 ft-lbs | 12.16 in-lbs | 0.1401 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
2.415 kN
543 lbf
Target tension across joint interface
75% Tap Drill d - P
2.261 mm
#43 (0.0890 in) (85% Eng.)
50% Hard Metal Drill: 2.502 mm
Direct Engineering Specification Summary
The recommended tightening torque for a #4-40 UNC Grade 8 bolt is 1.374 N·m (1.014 ft-lbs) when dry (K=0.20) and 1.031 N·m (0.76 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 2.415 kN (543 lbf) at 75% proof load. Standard 75% tap drill is #43 (0.0890 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 3.892 mm²
Pitch Diameter (d2) 2.432 mm
Minor Diameter (d1) 2.157 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (2.8448 − 0.9382 × 0.635)² = 3.892 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 3.892 mm² × 827.4 N/mm² = 3220 N (3.22 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 3220 N = 2415 N (2.415 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 2.8448 mm × 2415 N) / 1000 = 1.374 N·m (1.014 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
#4-40 UNC Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 | 0.973 Nm 0.718 ft-lb | 0.876 Nm 0.646 ft-lb | 0.73 Nm 0.538 ft-lb | 0.584 Nm 0.431 ft-lb | 1.711 | 2.281 |
| Grade 8 CURRENT | 1.374 Nm 1.014 ft-lb | 1.237 Nm 0.912 ft-lb | 1.031 Nm 0.76 ft-lb | 0.824 Nm 0.608 ft-lb | 2.415 | 3.22 |
| 18-8 Stainless | 0.515 Nm 0.38 ft-lb | 0.464 Nm 0.342 ft-lb | 0.387 Nm 0.285 ft-lb | 0.309 Nm 0.228 ft-lb | 0.906 | 1.208 |
Frequently Asked Engineering Questions (#4-40 UNC Grade 8)
What is the recommended tightening torque for a #4-40 UNC Grade 8 bolt?
For a #4-40 UNC SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 1.374 N·m (1.014 ft-lbs / 12.16 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1.031 N·m (0.76 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 0.824 N·m (0.608 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #4-40 UNC internal threads?
The standard cut tap drill size for #4-40 UNC is #43 (0.0890 in) (0.0890" / 2.261 mm), which delivers approximately 85% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 2.502 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #4-40 UNC Grade 8 fastener develop?
With a tensile stress area (As) of 3.892 mm² (0.00603 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a #4-40 UNC Grade 8 fastener possesses an ultimate proof load of 3.22 kN (723.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 2.415 kN (543 lbf) across the joint interface.
What clearance hole diameters should be drilled for #4-40 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #4-40 UNC fastener are: Close Fit = 3.048 mm (0.12"), Normal Fit = 3.264 mm (0.1285"), and Loose Fit = 3.658 mm (0.144"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.