Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

5/16"-24 UNF Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
26.142 N·m
19.281 ft-lbs | 231.38 in-lbs | 2.6657 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
16.467 kN
3,702 lbf
Target tension across joint interface
75% Tap Drill d - P
6.909 mm
I (0.2720 in) (89.8% Eng.)
50% Hard Metal Drill: 7.363 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 5/16"-24 UNF Grade 5 bolt is 26.142 N·m (19.281 ft-lbs) when dry (K=0.20) and 19.606 N·m (14.461 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 16.467 kN (3,702 lbf) at 75% proof load. Standard 75% tap drill is I (0.2720 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 7.9375 mm (0.3125") P = 1.05833 mm 5/16"-24 UNF Close: 8.204mm Normal: 8.433mm Loose: 8.738mm
Stress Area (As) 37.462 mm²
Pitch Diameter (d2) 7.25 mm
Minor Diameter (d1) 6.792 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (7.9375 − 0.9382 × 1.05833)² = 37.462 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 37.462 mm² × 586.1 N/mm² = 21956 N (21.956 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 21956 N = 16467 N (16.467 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 7.9375 mm × 16467 N) / 1000 = 26.142 N·m (19.281 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

5/16"-24 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 5/16"-24 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 26.142 Nm
19.281 ft-lb
23.528 Nm
17.353 ft-lb
19.606 Nm
14.461 ft-lb
15.685 Nm
11.569 ft-lb
16.467 21.956
Grade 8 36.905 Nm
27.219 ft-lb
33.214 Nm
24.498 ft-lb
27.679 Nm
20.415 ft-lb
22.143 Nm
16.332 ft-lb
23.247 30.996
18-8 Stainless 13.84 Nm
10.208 ft-lb
12.456 Nm
9.187 ft-lb
10.38 Nm
7.656 ft-lb
8.304 Nm
6.125 ft-lb
8.718 11.624

Frequently Asked Engineering Questions (5/16"-24 UNF Grade 5)

What is the recommended tightening torque for a 5/16"-24 UNF Grade 5 bolt?
For a 5/16"-24 UNF SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 26.142 N·m (19.281 ft-lbs / 231.38 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 19.606 N·m (14.461 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 15.685 N·m (11.569 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 5/16"-24 UNF internal threads?
The standard cut tap drill size for 5/16"-24 UNF is I (0.2720 in) (0.2720" / 6.909 mm), which delivers approximately 89.8% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 7.363 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 5/16"-24 UNF Grade 5 fastener develop?
With a tensile stress area (As) of 37.462 mm² (0.05807 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 5/16"-24 UNF Grade 5 fastener possesses an ultimate proof load of 21.956 kN (4,936 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 16.467 kN (3,702 lbf) across the joint interface.
What clearance hole diameters should be drilled for 5/16"-24 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 5/16"-24 UNF fastener are: Close Fit = 8.204 mm (0.323"), Normal Fit = 8.433 mm (0.332"), and Loose Fit = 8.738 mm (0.344"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.