Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

9/16"-12 UNC Grade 8 Torque & Tap Drill Spec

SAE J429 / ASTM A354 Grade BD

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
208.146 N·m
153.521 ft-lbs | 1842.25 in-lbs | 21.225 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
72.842 kN
16,375.5 lbf
Target tension across joint interface
75% Tap Drill d - P
12.304 mm
31/64" (0.4844 in) (86.6% Eng.)
50% Hard Metal Drill: 13.142 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 9/16"-12 UNC Grade 8 bolt is 208.146 N·m (153.521 ft-lbs) when dry (K=0.20) and 156.11 N·m (115.14 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 72.842 kN (16,375.5 lbf) at 75% proof load. Standard 75% tap drill is 31/64" (0.4844 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 14.2875 mm (0.5625") P = 2.11667 mm 9/16"-12 UNC Close: 14.681mm Normal: 15.088mm Loose: 15.875mm
Stress Area (As) 117.383 mm²
Pitch Diameter (d2) 12.913 mm
Minor Diameter (d1) 11.996 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (14.2875 − 0.9382 × 2.11667)² = 117.383 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 117.383 mm² × 827.4 N/mm² = 97123 N (97.123 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 97123 N = 72842 N (72.842 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 14.2875 mm × 72842 N) / 1000 = 208.146 N·m (153.521 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

9/16"-12 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 9/16"-12 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 147.443 Nm
108.748 ft-lb
132.699 Nm
97.874 ft-lb
110.582 Nm
81.561 ft-lb
88.466 Nm
65.249 ft-lb
51.599 68.798
Grade 8 CURRENT 208.146 Nm
153.521 ft-lb
187.331 Nm
138.169 ft-lb
156.11 Nm
115.14 ft-lb
124.888 Nm
92.112 ft-lb
72.842 97.123
18-8 Stainless 78.061 Nm
57.575 ft-lb
70.255 Nm
51.817 ft-lb
58.546 Nm
43.181 ft-lb
46.837 Nm
34.545 ft-lb
27.318 36.424

Frequently Asked Engineering Questions (9/16"-12 UNC Grade 8)

What is the recommended tightening torque for a 9/16"-12 UNC Grade 8 bolt?
For a 9/16"-12 UNC SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 208.146 N·m (153.521 ft-lbs / 1842.25 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 156.11 N·m (115.14 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 124.888 N·m (92.112 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 9/16"-12 UNC internal threads?
The standard cut tap drill size for 9/16"-12 UNC is 31/64" (0.4844 in) (0.4844" / 12.304 mm), which delivers approximately 86.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 13.142 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 9/16"-12 UNC Grade 8 fastener develop?
With a tensile stress area (As) of 117.383 mm² (0.18194 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a 9/16"-12 UNC Grade 8 fastener possesses an ultimate proof load of 97.123 kN (21,834.1 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 72.842 kN (16,375.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for 9/16"-12 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 9/16"-12 UNC fastener are: Close Fit = 14.681 mm (0.578"), Normal Fit = 15.088 mm (0.594"), and Loose Fit = 15.875 mm (0.625"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.