9/16"-12 UNC Grade 5 Torque & Tap Drill Spec
SAE J429 / ASTM A449Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
147.443 N·m
108.748 ft-lbs | 1304.98 in-lbs | 15.035 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
51.599 kN
11,599.8 lbf
Target tension across joint interface
75% Tap Drill d - P
12.304 mm
31/64" (0.4844 in) (86.6% Eng.)
50% Hard Metal Drill: 13.142 mm
Direct Engineering Specification Summary
The recommended tightening torque for a 9/16"-12 UNC Grade 5 bolt is 147.443 N·m (108.748 ft-lbs) when dry (K=0.20) and 110.582 N·m (81.561 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 51.599 kN (11,599.8 lbf) at 75% proof load. Standard 75% tap drill is 31/64" (0.4844 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 117.383 mm²
Pitch Diameter (d2) 12.913 mm
Minor Diameter (d1) 11.996 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (14.2875 − 0.9382 × 2.11667)² = 117.383 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 117.383 mm² × 586.1 N/mm² = 68798 N (68.798 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 68798 N = 51599 N (51.599 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 14.2875 mm × 51599 N) / 1000 = 147.443 N·m (108.748 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
9/16"-12 UNC Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 CURRENT | 147.443 Nm 108.748 ft-lb | 132.699 Nm 97.874 ft-lb | 110.582 Nm 81.561 ft-lb | 88.466 Nm 65.249 ft-lb | 51.599 | 68.798 |
| Grade 8 | 208.146 Nm 153.521 ft-lb | 187.331 Nm 138.169 ft-lb | 156.11 Nm 115.14 ft-lb | 124.888 Nm 92.112 ft-lb | 72.842 | 97.123 |
| 18-8 Stainless | 78.061 Nm 57.575 ft-lb | 70.255 Nm 51.817 ft-lb | 58.546 Nm 43.181 ft-lb | 46.837 Nm 34.545 ft-lb | 27.318 | 36.424 |
Frequently Asked Engineering Questions (9/16"-12 UNC Grade 5)
What is the recommended tightening torque for a 9/16"-12 UNC Grade 5 bolt?
For a 9/16"-12 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 147.443 N·m (108.748 ft-lbs / 1304.98 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 110.582 N·m (81.561 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 88.466 N·m (65.249 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 9/16"-12 UNC internal threads?
The standard cut tap drill size for 9/16"-12 UNC is 31/64" (0.4844 in) (0.4844" / 12.304 mm), which delivers approximately 86.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 13.142 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 9/16"-12 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 117.383 mm² (0.18194 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 9/16"-12 UNC Grade 5 fastener possesses an ultimate proof load of 68.798 kN (15,466.4 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 51.599 kN (11,599.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for 9/16"-12 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 9/16"-12 UNC fastener are: Close Fit = 14.681 mm (0.578"), Normal Fit = 15.088 mm (0.594"), and Loose Fit = 15.875 mm (0.625"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.