Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M10 x 1.25 Class 8.8 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
55.078 N·m
40.624 ft-lbs | 487.48 in-lbs | 5.6164 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
27.539 kN
6,191 lbf
Target tension across joint interface
75% Tap Drill d - P
8.8 mm
8.8 mm (88.7% Eng.)
50% Hard Metal Drill: 9.323 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M10 x 1.25 Class 8.8 bolt is 55.078 N·m (40.624 ft-lbs) when dry (K=0.20) and 41.309 N·m (30.468 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 27.539 kN (6,191 lbf) at 75% proof load. Standard 75% tap drill is 8.8 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 10 mm (0.3937") P = 1.25 mm M10 x 1.25 Close: 10.5mm Normal: 11mm Loose: 12mm
Stress Area (As) 61.198 mm²
Pitch Diameter (d2) 9.188 mm
Minor Diameter (d1) 8.647 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (10 − 0.9382 × 1.25)² = 61.198 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 61.198 mm² × 600 N/mm² = 36719 N (36.719 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 36719 N = 27539 N (27.539 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 10 mm × 27539 N) / 1000 = 55.078 N·m (40.624 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M10 x 1.25 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M10 x 1.25
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 CURRENT 55.078 Nm
40.624 ft-lb
49.57 Nm
36.561 ft-lb
41.309 Nm
30.468 ft-lb
33.047 Nm
24.374 ft-lb
27.539 36.719
Class 10.9 76.192 Nm
56.196 ft-lb
68.572 Nm
50.576 ft-lb
57.144 Nm
42.147 ft-lb
45.715 Nm
33.718 ft-lb
38.096 50.794
Class 12.9 89.043 Nm
65.675 ft-lb
80.139 Nm
59.107 ft-lb
66.782 Nm
49.256 ft-lb
53.426 Nm
39.405 ft-lb
44.522 59.362
A2-70 Stainless 41.309 Nm
30.468 ft-lb
37.178 Nm
27.421 ft-lb
30.981 Nm
22.851 ft-lb
24.785 Nm
18.281 ft-lb
20.654 27.539
A4-80 Marine Stainless 55.078 Nm
40.624 ft-lb
49.57 Nm
36.561 ft-lb
41.309 Nm
30.468 ft-lb
33.047 Nm
24.374 ft-lb
27.539 36.719

Frequently Asked Engineering Questions (M10 x 1.25 Class 8.8)

What is the recommended tightening torque for a M10 x 1.25 Class 8.8 bolt?
For a M10 x 1.25 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 55.078 N·m (40.624 ft-lbs / 487.48 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 41.309 N·m (30.468 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 33.047 N·m (24.374 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M10 x 1.25 internal threads?
The standard cut tap drill size for M10 x 1.25 is 8.8 mm (0.3465" / 8.8 mm), which delivers approximately 88.7% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 9.323 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M10 x 1.25 Class 8.8 fastener develop?
With a tensile stress area (As) of 61.198 mm² (0.09486 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M10 x 1.25 Class 8.8 fastener possesses an ultimate proof load of 36.719 kN (8,254.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 27.539 kN (6,191 lbf) across the joint interface.
What clearance hole diameters should be drilled for M10 x 1.25 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M10 x 1.25 fastener are: Close Fit = 10.5 mm (0.4134"), Normal Fit = 11 mm (0.4331"), and Loose Fit = 12 mm (0.4724"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.