M10 x 1.25 A4-80 Marine Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
55.078 N·m
40.624 ft-lbs | 487.48 in-lbs | 5.6164 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
27.539 kN
6,191 lbf
Target tension across joint interface
75% Tap Drill d - P
8.8 mm
8.8 mm (88.7% Eng.)
50% Hard Metal Drill: 9.323 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M10 x 1.25 A4-80 Marine Stainless bolt is 55.078 N·m (40.624 ft-lbs) when dry (K=0.20) and 41.309 N·m (30.468 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 27.539 kN (6,191 lbf) at 75% proof load. Standard 75% tap drill is 8.8 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 61.198 mm²
Pitch Diameter (d2) 9.188 mm
Minor Diameter (d1) 8.647 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (10 − 0.9382 × 1.25)² = 61.198 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 61.198 mm² × 600 N/mm² = 36719 N (36.719 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 36719 N = 27539 N (27.539 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 10 mm × 27539 N) / 1000 = 55.078 N·m (40.624 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M10 x 1.25 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 55.078 Nm 40.624 ft-lb | 49.57 Nm 36.561 ft-lb | 41.309 Nm 30.468 ft-lb | 33.047 Nm 24.374 ft-lb | 27.539 | 36.719 |
| Class 10.9 | 76.192 Nm 56.196 ft-lb | 68.572 Nm 50.576 ft-lb | 57.144 Nm 42.147 ft-lb | 45.715 Nm 33.718 ft-lb | 38.096 | 50.794 |
| Class 12.9 | 89.043 Nm 65.675 ft-lb | 80.139 Nm 59.107 ft-lb | 66.782 Nm 49.256 ft-lb | 53.426 Nm 39.405 ft-lb | 44.522 | 59.362 |
| A2-70 Stainless | 41.309 Nm 30.468 ft-lb | 37.178 Nm 27.421 ft-lb | 30.981 Nm 22.851 ft-lb | 24.785 Nm 18.281 ft-lb | 20.654 | 27.539 |
| A4-80 Marine Stainless CURRENT | 55.078 Nm 40.624 ft-lb | 49.57 Nm 36.561 ft-lb | 41.309 Nm 30.468 ft-lb | 33.047 Nm 24.374 ft-lb | 27.539 | 36.719 |
Frequently Asked Engineering Questions (M10 x 1.25 A4-80 Marine Stainless)
What is the recommended tightening torque for a M10 x 1.25 A4-80 Marine Stainless bolt?
For a M10 x 1.25 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 55.078 N·m (40.624 ft-lbs / 487.48 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 41.309 N·m (30.468 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 33.047 N·m (24.374 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M10 x 1.25 internal threads?
The standard cut tap drill size for M10 x 1.25 is 8.8 mm (0.3465" / 8.8 mm), which delivers approximately 88.7% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 9.323 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M10 x 1.25 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 61.198 mm² (0.09486 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M10 x 1.25 A4-80 Marine Stainless fastener possesses an ultimate proof load of 36.719 kN (8,254.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 27.539 kN (6,191 lbf) across the joint interface.
What clearance hole diameters should be drilled for M10 x 1.25 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M10 x 1.25 fastener are: Close Fit = 10.5 mm (0.4134"), Normal Fit = 11 mm (0.4331"), and Loose Fit = 12 mm (0.4724"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.