Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M12 x 1.75 Class 12.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
147.128 N·m
108.516 ft-lbs | 1302.2 in-lbs | 15.0029 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
61.304 kN
13,781.6 lbf
Target tension across joint interface
75% Tap Drill d - P
10.2 mm
10.2 mm (95% Eng.)
50% Hard Metal Drill: 11.053 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M12 x 1.75 Class 12.9 bolt is 147.128 N·m (108.516 ft-lbs) when dry (K=0.20) and 110.346 N·m (81.387 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 61.304 kN (13,781.6 lbf) at 75% proof load. Standard 75% tap drill is 10.2 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 12 mm (0.4724") P = 1.75 mm M12 x 1.75 Close: 13mm Normal: 13.5mm Loose: 14.5mm
Stress Area (As) 84.266 mm²
Pitch Diameter (d2) 10.863 mm
Minor Diameter (d1) 10.106 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (12 − 0.9382 × 1.75)² = 84.266 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 84.266 mm² × 970 N/mm² = 81738 N (81.738 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 81738 N = 61304 N (61.304 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 12 mm × 61304 N) / 1000 = 147.128 N·m (108.516 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M12 x 1.75 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M12 x 1.75
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 91.007 Nm
67.124 ft-lb
81.907 Nm
60.411 ft-lb
68.255 Nm
50.343 ft-lb
54.604 Nm
40.274 ft-lb
37.92 50.56
Class 10.9 125.893 Nm
92.854 ft-lb
113.304 Nm
83.569 ft-lb
94.42 Nm
69.641 ft-lb
75.536 Nm
55.713 ft-lb
52.456 69.941
Class 12.9 CURRENT 147.128 Nm
108.516 ft-lb
132.416 Nm
97.665 ft-lb
110.346 Nm
81.387 ft-lb
88.277 Nm
65.11 ft-lb
61.304 81.738
A2-70 Stainless 68.255 Nm
50.343 ft-lb
61.43 Nm
45.308 ft-lb
51.192 Nm
37.757 ft-lb
40.953 Nm
30.206 ft-lb
28.44 37.92
A4-80 Marine Stainless 91.007 Nm
67.124 ft-lb
81.907 Nm
60.411 ft-lb
68.255 Nm
50.343 ft-lb
54.604 Nm
40.274 ft-lb
37.92 50.56

Frequently Asked Engineering Questions (M12 x 1.75 Class 12.9)

What is the recommended tightening torque for a M12 x 1.75 Class 12.9 bolt?
For a M12 x 1.75 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 147.128 N·m (108.516 ft-lbs / 1302.2 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 110.346 N·m (81.387 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 88.277 N·m (65.11 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M12 x 1.75 internal threads?
The standard cut tap drill size for M12 x 1.75 is 10.2 mm (0.4016" / 10.2 mm), which delivers approximately 95% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 11.053 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M12 x 1.75 Class 12.9 fastener develop?
With a tensile stress area (As) of 84.266 mm² (0.13061 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M12 x 1.75 Class 12.9 fastener possesses an ultimate proof load of 81.738 kN (18,375.4 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 61.304 kN (13,781.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for M12 x 1.75 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M12 x 1.75 fastener are: Close Fit = 13 mm (0.5118"), Normal Fit = 13.5 mm (0.5315"), and Loose Fit = 14.5 mm (0.5709"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.