M12 x 1.75 A4-80 Marine Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
91.007 N·m
67.124 ft-lbs | 805.48 in-lbs | 9.2802 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
37.92 kN
8,524.7 lbf
Target tension across joint interface
75% Tap Drill d - P
10.2 mm
10.2 mm (95% Eng.)
50% Hard Metal Drill: 11.053 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M12 x 1.75 A4-80 Marine Stainless bolt is 91.007 N·m (67.124 ft-lbs) when dry (K=0.20) and 68.255 N·m (50.343 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 37.92 kN (8,524.7 lbf) at 75% proof load. Standard 75% tap drill is 10.2 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 84.266 mm²
Pitch Diameter (d2) 10.863 mm
Minor Diameter (d1) 10.106 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (12 − 0.9382 × 1.75)² = 84.266 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 84.266 mm² × 600 N/mm² = 50560 N (50.56 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 50560 N = 37920 N (37.92 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 12 mm × 37920 N) / 1000 = 91.007 N·m (67.124 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M12 x 1.75 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 91.007 Nm 67.124 ft-lb | 81.907 Nm 60.411 ft-lb | 68.255 Nm 50.343 ft-lb | 54.604 Nm 40.274 ft-lb | 37.92 | 50.56 |
| Class 10.9 | 125.893 Nm 92.854 ft-lb | 113.304 Nm 83.569 ft-lb | 94.42 Nm 69.641 ft-lb | 75.536 Nm 55.713 ft-lb | 52.456 | 69.941 |
| Class 12.9 | 147.128 Nm 108.516 ft-lb | 132.416 Nm 97.665 ft-lb | 110.346 Nm 81.387 ft-lb | 88.277 Nm 65.11 ft-lb | 61.304 | 81.738 |
| A2-70 Stainless | 68.255 Nm 50.343 ft-lb | 61.43 Nm 45.308 ft-lb | 51.192 Nm 37.757 ft-lb | 40.953 Nm 30.206 ft-lb | 28.44 | 37.92 |
| A4-80 Marine Stainless CURRENT | 91.007 Nm 67.124 ft-lb | 81.907 Nm 60.411 ft-lb | 68.255 Nm 50.343 ft-lb | 54.604 Nm 40.274 ft-lb | 37.92 | 50.56 |
Frequently Asked Engineering Questions (M12 x 1.75 A4-80 Marine Stainless)
What is the recommended tightening torque for a M12 x 1.75 A4-80 Marine Stainless bolt?
For a M12 x 1.75 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 91.007 N·m (67.124 ft-lbs / 805.48 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 68.255 N·m (50.343 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 54.604 N·m (40.274 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M12 x 1.75 internal threads?
The standard cut tap drill size for M12 x 1.75 is 10.2 mm (0.4016" / 10.2 mm), which delivers approximately 95% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 11.053 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M12 x 1.75 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 84.266 mm² (0.13061 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M12 x 1.75 A4-80 Marine Stainless fastener possesses an ultimate proof load of 50.56 kN (11,366.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 37.92 kN (8,524.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for M12 x 1.75 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M12 x 1.75 fastener are: Close Fit = 13 mm (0.5118"), Normal Fit = 13.5 mm (0.5315"), and Loose Fit = 14.5 mm (0.5709"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.