M14 x 1.5 A4-80 Marine Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
156.927 N·m
115.743 ft-lbs | 1388.92 in-lbs | 16.0021 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
56.045 kN
12,599.5 lbf
Target tension across joint interface
75% Tap Drill d - P
12.5 mm
12.5 mm (92.4% Eng.)
50% Hard Metal Drill: 13.188 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M14 x 1.5 A4-80 Marine Stainless bolt is 156.927 N·m (115.743 ft-lbs) when dry (K=0.20) and 117.695 N·m (86.807 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 56.045 kN (12,599.5 lbf) at 75% proof load. Standard 75% tap drill is 12.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 124.545 mm²
Pitch Diameter (d2) 13.026 mm
Minor Diameter (d1) 12.376 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (14 − 0.9382 × 1.5)² = 124.545 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 124.545 mm² × 600 N/mm² = 74727 N (74.727 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 74727 N = 56045 N (56.045 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 14 mm × 56045 N) / 1000 = 156.927 N·m (115.743 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M14 x 1.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 156.927 Nm 115.743 ft-lb | 141.234 Nm 104.169 ft-lb | 117.695 Nm 86.807 ft-lb | 94.156 Nm 69.446 ft-lb | 56.045 | 74.727 |
| Class 10.9 | 217.082 Nm 160.111 ft-lb | 195.374 Nm 144.1 ft-lb | 162.811 Nm 120.084 ft-lb | 130.249 Nm 96.067 ft-lb | 77.529 | 103.372 |
| Class 12.9 | 253.698 Nm 187.118 ft-lb | 228.328 Nm 168.406 ft-lb | 190.274 Nm 140.339 ft-lb | 152.219 Nm 112.271 ft-lb | 90.606 | 120.809 |
| A2-70 Stainless | 117.695 Nm 86.807 ft-lb | 105.926 Nm 78.127 ft-lb | 88.271 Nm 65.106 ft-lb | 70.617 Nm 52.084 ft-lb | 42.034 | 56.045 |
| A4-80 Marine Stainless CURRENT | 156.927 Nm 115.743 ft-lb | 141.234 Nm 104.169 ft-lb | 117.695 Nm 86.807 ft-lb | 94.156 Nm 69.446 ft-lb | 56.045 | 74.727 |
Frequently Asked Engineering Questions (M14 x 1.5 A4-80 Marine Stainless)
What is the recommended tightening torque for a M14 x 1.5 A4-80 Marine Stainless bolt?
For a M14 x 1.5 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 156.927 N·m (115.743 ft-lbs / 1388.92 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 117.695 N·m (86.807 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 94.156 N·m (69.446 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M14 x 1.5 internal threads?
The standard cut tap drill size for M14 x 1.5 is 12.5 mm (0.4921" / 12.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 13.188 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M14 x 1.5 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 124.545 mm² (0.19305 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M14 x 1.5 A4-80 Marine Stainless fastener possesses an ultimate proof load of 74.727 kN (16,799.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 56.045 kN (12,599.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for M14 x 1.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M14 x 1.5 fastener are: Close Fit = 15 mm (0.5906"), Normal Fit = 15.5 mm (0.6102"), and Loose Fit = 16.5 mm (0.6496"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.