Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M16 x 2.0 A4-80 Marine Stainless Torque & Tap Drill Spec

ISO 3506-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
225.602 N·m
166.395 ft-lbs | 1996.75 in-lbs | 23.005 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
70.501 kN
15,849.2 lbf
Target tension across joint interface
75% Tap Drill d - P
14 mm
14 mm (92.4% Eng.)
50% Hard Metal Drill: 14.917 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M16 x 2.0 A4-80 Marine Stainless bolt is 225.602 N·m (166.395 ft-lbs) when dry (K=0.20) and 169.201 N·m (124.797 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 70.501 kN (15,849.2 lbf) at 75% proof load. Standard 75% tap drill is 14 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 16 mm (0.6299") P = 2 mm M16 x 2.0 Close: 17mm Normal: 17.5mm Loose: 18.5mm
Stress Area (As) 156.668 mm²
Pitch Diameter (d2) 14.701 mm
Minor Diameter (d1) 13.835 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (16 − 0.9382 × 2)² = 156.668 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 156.668 mm² × 600 N/mm² = 94001 N (94.001 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 94001 N = 70501 N (70.501 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 16 mm × 70501 N) / 1000 = 225.602 N·m (166.395 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M16 x 2.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M16 x 2.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 225.602 Nm
166.395 ft-lb
203.042 Nm
149.756 ft-lb
169.201 Nm
124.797 ft-lb
135.361 Nm
99.837 ft-lb
70.501 94.001
Class 10.9 312.083 Nm
230.18 ft-lb
280.874 Nm
207.162 ft-lb
234.062 Nm
172.635 ft-lb
187.25 Nm
138.108 ft-lb
97.526 130.034
Class 12.9 364.723 Nm
269.006 ft-lb
328.251 Nm
242.105 ft-lb
273.542 Nm
201.754 ft-lb
218.834 Nm
161.404 ft-lb
113.976 151.968
A2-70 Stainless 169.201 Nm
124.797 ft-lb
152.281 Nm
112.317 ft-lb
126.901 Nm
93.597 ft-lb
101.521 Nm
74.878 ft-lb
52.875 70.501
A4-80 Marine Stainless CURRENT 225.602 Nm
166.395 ft-lb
203.042 Nm
149.756 ft-lb
169.201 Nm
124.797 ft-lb
135.361 Nm
99.837 ft-lb
70.501 94.001

Frequently Asked Engineering Questions (M16 x 2.0 A4-80 Marine Stainless)

What is the recommended tightening torque for a M16 x 2.0 A4-80 Marine Stainless bolt?
For a M16 x 2.0 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 225.602 N·m (166.395 ft-lbs / 1996.75 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 169.201 N·m (124.797 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 135.361 N·m (99.837 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M16 x 2.0 internal threads?
The standard cut tap drill size for M16 x 2.0 is 14 mm (0.5512" / 14 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 14.917 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M16 x 2.0 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 156.668 mm² (0.24284 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M16 x 2.0 A4-80 Marine Stainless fastener possesses an ultimate proof load of 94.001 kN (21,132.2 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 70.501 kN (15,849.2 lbf) across the joint interface.
What clearance hole diameters should be drilled for M16 x 2.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M16 x 2.0 fastener are: Close Fit = 17 mm (0.6693"), Normal Fit = 17.5 mm (0.689"), and Loose Fit = 18.5 mm (0.7283"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.