M16 x 1.5 A2-70 Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
180.628 N·m
133.224 ft-lbs | 1598.69 in-lbs | 18.4189 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
56.446 kN
12,689.6 lbf
Target tension across joint interface
75% Tap Drill d - P
14.5 mm
14.5 mm (92.4% Eng.)
50% Hard Metal Drill: 15.188 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M16 x 1.5 A2-70 Stainless bolt is 180.628 N·m (133.224 ft-lbs) when dry (K=0.20) and 135.471 N·m (99.918 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 56.446 kN (12,689.6 lbf) at 75% proof load. Standard 75% tap drill is 14.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 167.248 mm²
Pitch Diameter (d2) 15.026 mm
Minor Diameter (d1) 14.376 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (16 − 0.9382 × 1.5)² = 167.248 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 167.248 mm² × 450 N/mm² = 75262 N (75.262 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 75262 N = 56446 N (56.446 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 16 mm × 56446 N) / 1000 = 180.628 N·m (133.224 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M16 x 1.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 240.837 Nm 177.632 ft-lb | 216.753 Nm 159.869 ft-lb | 180.628 Nm 133.224 ft-lb | 144.502 Nm 106.579 ft-lb | 75.262 | 100.349 |
| Class 10.9 | 333.158 Nm 245.725 ft-lb | 299.842 Nm 221.152 ft-lb | 249.869 Nm 184.294 ft-lb | 199.895 Nm 147.435 ft-lb | 104.112 | 138.816 |
| Class 12.9 | 389.353 Nm 287.172 ft-lb | 350.418 Nm 258.455 ft-lb | 292.015 Nm 215.379 ft-lb | 233.612 Nm 172.303 ft-lb | 121.673 | 162.231 |
| A2-70 Stainless CURRENT | 180.628 Nm 133.224 ft-lb | 162.565 Nm 119.902 ft-lb | 135.471 Nm 99.918 ft-lb | 108.377 Nm 79.935 ft-lb | 56.446 | 75.262 |
| A4-80 Marine Stainless | 240.837 Nm 177.632 ft-lb | 216.753 Nm 159.869 ft-lb | 180.628 Nm 133.224 ft-lb | 144.502 Nm 106.579 ft-lb | 75.262 | 100.349 |
Frequently Asked Engineering Questions (M16 x 1.5 A2-70 Stainless)
What is the recommended tightening torque for a M16 x 1.5 A2-70 Stainless bolt?
For a M16 x 1.5 Stainless Steel A2-70 (AISI 304 / EN 1.4301) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 180.628 N·m (133.224 ft-lbs / 1598.69 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 135.471 N·m (99.918 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 108.377 N·m (79.935 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M16 x 1.5 internal threads?
The standard cut tap drill size for M16 x 1.5 is 14.5 mm (0.5709" / 14.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 15.188 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M16 x 1.5 A2-70 Stainless fastener develop?
With a tensile stress area (As) of 167.248 mm² (0.25924 in²) and a nominal proof stress of 450 MPa (65,267 psi), a M16 x 1.5 A2-70 Stainless fastener possesses an ultimate proof load of 75.262 kN (16,919.5 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 56.446 kN (12,689.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for M16 x 1.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M16 x 1.5 fastener are: Close Fit = 17 mm (0.6693"), Normal Fit = 17.5 mm (0.689"), and Loose Fit = 18.5 mm (0.7283"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.